 | | | Red Hat Linux 9 | | Hello -
I am trying to re-install RH9 on a small older computer (500mhz Celeron
256k ram. 8g hdd)-
Anaconda starts recognizes ALL my hardware inlcluding two Linksys
LNE100TX NIC 's. I go througOn Tue 2 Dec 2003 Jim Laverty wrote
> Anyone from Red Hat notice that the source rpms on Red Hat 's site doesn 't
> contain the source for either RH 7.3 or RH 9 for the new 2.4.20-24.x
> kernel(s)?
i realize up2date support is going away but until it is completely gone
i want to make use of it.
however i the last few times i tried to update my demo registered
server i get a message telliAnyone from Red Hat notice that the source rpms on Red Hat 's site doesn 't
contain the source for either RH 7.3 or RH 9 for the new 2.4.20-24.x
kernel(s)?
Note
This message is for the named personOn Tue Dec 02 2003 at 08 56 54AM -0600 Aaron Konstam wrote
> On Tue Dec 02 2003 at 10 06 55AM +0100 Kurt Richter wrote
> > Melissa Golter schrieb
> > >
> > So far as I now redhat has the routProblem when a network connection a b.c.16 xxxx - > a.b.c.20 yyyy
fails it is
to be re-established as soon as possible but the addresses
0.0.0.0 xxxx (listening for 1+ connect() calls)
and
a.b.c.dHi
I installed a new driver and to activate it I always must issue the
command "modprobe saa7134 ".
What should I do in order that module was loaded automaticly during
system startup ? - modprobe manwhy in RH 9 does the screen keep refreshing while booting and what
purpose does this serve?
the boot screen refreshes or flashes 3 or 4 times while booting.
irritating!
jay
Hi
Currently I am passing vga 791 to the kernel to get a bootup screen
size of 1280x1024. Since my actual screen res is 1400x1050 I would like to
get to this size.
I 'm not sure what parameters t
Does anyone know about netorking -- and why a linux box would have
troubles when connecting to a unix server? I have checked through some
firewall issues and consulted people from the unix side andSince Alan Cox is busy with some _other_ stuffs and the last -ac series was
the 2.4.22-ac4 and I wanted the New "Laptop_mode " I did some hacking of my
own.
So.. Here 's the patch for cpufreq (taken Hello
I installed redhat 9 for some server purposes but I 'm not an expert really
when I installed the server I was
really a newbie so I made a big mistake.
I put all the information in one partiAt 11 42 AM 12/1/2003 Guy Fraser had this to say
>I just googled for "canadian privacy act " and got loads of hits.
>
>Here is a reasonable article explaining the respocibilies of international
>How can I find out what if any patch-o-matic patches
have been applied to the Red Hat Linux 9 distribution
of IPTables?
I just googled for "canadian privacy act " and got loads of hits.
Here is a reasonable article explaining the respocibilies of international
firms dealing with the Canadian law.
http //www.gigalaw.cAll open office apps seg fault. Here is the end of strace on
oowriter. It seems it seg faults loading fonts. I do have a lot of
fonts installed...
open( "/usr/share/fonts/monotype/Extream/fingerpr.Hi
My customer would like an all-in-one printer/scanner/copy working
perfectly under RH9.
As I am looking on the web I found some models but many seems to work
partially and other not at all (LAt 10 17 AM 11/28/2003 Guy Fraser had this to say
>4) In Canada as of Jan 2004 Any mail on the mail server must be available
>to the
>customer even if the account is suspended all new mail muTrying to install the Eterm rpm from
http //www.eterm.org/download/
$ sudo rpm -Uvh Eterm-0.9.2-4.i386.rpm
error Failed dependencies
libast.so.2 is needed by Eterm-0.9.2-4
$ sudo rpm -q lHi
Has anyone been able to get Gaim to work with MSN. I keep gettting..
YOu need "SSL " support. I have mozilla-nss and also GNUTLS installed but
seems to me gaim either
1. can 't find them.. (Is tI get this typically 3 or 4 times a day in the syslog (and on console)
on a new install of RH 9 on a 2.8Mhz Intel machine (intel chipset)
What is this telling me that I should know?
Thanks
Craig
update -
I accidentally left the linux disk in the drive when I went back to windows
and lo and behold windows can read it perfectly! So it seams that linux
will write a file that can be read by Hi folks
I am configuring printer hp deskjet 690C starting from Control
Center. Everything seemed going on without problem. I selected lp0
printer and made a test print out "Printed Using CUPTake a look at this screenshot
http //www.fibrespeed.net/~mbabcock/linux/images/desktop-19991224-02.png
It 's one of many screenshots that show a nice system monitor on the
right side with system CPHi everyone.
I just updated my packages via up2date. Among the updates were XFree86
packages (I 'll give a full list at the bottom). Somehow the update caused
the following two strange behaviours
A few days ago I accidently hit the Auto-Sync button on my NEC MultiSync
LCD1920NX LCD and now the screen has shifted about an inch to the right
leaving a gap on the left side of the display.
I of coIs it possible to upgrade to Fedora Core 1 from RH 9.0?
I am also considering switching to Debian Woody or Sarge on another
box. Debian releases seem to be slower more tested than RH.
Anyone had expwhat I need is rename '/home ' as '/something '.
'/home ' is a filesystem on '/dev/hda5 '..
is this as simple as a rename or mv....
I 'm concern about the data it holds
Hi
I don 't understand - why is it like that ?
1) From http //www.kernel.org/ one can download the stable linux kernel in
2.4.23 version but on Red Hat 's web site there is "only " 2.4.20-20.9
versionIs gated part of the RH distro?
I can 't seem to find it.
Koos.
|
|
|
