 | | | Enterprise Linux 3 | |
Hi everyone
I 'm trying to setup a temporary RHEL3 machine to reproduce a
software problem on RHEL3U2 (not RHEL 's problem it 's the software).
The only system I have available for this rOliverio Diaz wrote
>We have a DELL Power Edge 1600 SC (XEON Processor and 1GB RAM) and
>have noticed that the OS leaks memory.
>When I first boot the system the memory chunks where of 8Kb. AftI wanted to ask if anyone has seen strange NFS behavior on the U4 kernel
(specifically 2.4.21-27.0.1.EL) when doing lots of little-file IO to a
back-end NAS storage device (Netapp filer in this caseOn Wed 26 Jan 2005 Craig White wrote
> and I am too dumb to figure out the difference between grep and egrep.
> When the agrep curveball came through this list and the juju stuff it
> outputsHow would one go about verifying that patch for a vulnerability (ex. CVE
number CAN-2003-0693) has been back-ported on a RHEL3 system?
I 'm trying to go through the errata but I 'm only finding reI personaly have had pretty good luck with the HP drivers. The main
reason I load them is to find out when hardware fails (drives fans
etc.) Do people have another way to do this or do you just I agree. The HP system health drivers are poorly written. We have had
lockups 100% CPU utilization and other issues relating to these
modules. You would think the #1 server vendor would have a more > On Tue 25 Jan 2005 Thomas Cameron wrote
>
> > Say I have an RHEL 3 machine that I installed and I didn 't check the box
> > for
> > say printing support. Now I decide I want printing support. -----BEGIN PGP SIGNED MESSAGE-----
Hash SHA1
Arjan van de Ven wrote
| On Tue 2005-01-25 at 15 00 +0100 Mimmus wrote
|
| > HP reccomends installation of HP System Health Application and
|On Tue 2005-01-25 at 15 00 +0100 Mimmus wrote
> HP reccomends installation of HP System Health Application and Insight
> Management Agents for RH3
> http //h18023.www1.hp.com/support/files/seSay I have an RHEL 3 machine that I installed and I didn 't check the box
for say printing support. Now I decide I want printing support. Is there
an easy way with up2date to get all of the manHi everyone
I am fairly new to this list... We are running a taroon beta with
updated recompiled SRPMS from redhat....
I am currently trying to rebuild php so it has xslt support (using
sabloHi
I have a HP DL740 server with two NC7781 Network Adapters.
RH 3 loads tg3 driver HP reccommends bcm5700 instead.
What is your opinion?
Thx
Domenico Viggiani
--
Taroon-list mailing liRoger Pe?a Escobio wrote
>the spec that come with courier-authlib "call " the make command with the opcion
>%{_smp_mflags} which mean in my case that make is called with the opcion -j8 when thiHi
anybody saw disk I/O degradation with current (2.4.21-27+) kernels?
After hours or days I have a lot of disc intensive processes in D state
and every disc operation is very slow (but with nHP reccomends installation of HP System Health Application and Insight
Management Agents for RH3
http //h18023.www1.hp.com/support/files/server/us/download/22093.html
During installation it aIs /dev/nvram supported for direct access to system BIOS? Certain
programs (tpb -- Thinkpad buttons) rely on /dev/nvram. I 've never
gotten tpb to work on RHEL 3.
Using the volume buttons on my Is there support for posix mqueue (/dev/mqueue) on the current RHEL?
(We need this to run a SCADA system)
When is the next version due? Will it contain posix mqueue?
To test if it contains the Hi all
I have lots of storage in a large Solaris samfs environment that is NFS
shared to a large number of Solaris and RHEL3 clients. Under some conditions
linux apps have been getting stale I am trying to install the GD perl module via CPAN. But it seems to be
failing and I am getting the below errors. Has anyone else come across this?
Where is libgd installed? [/usr/lib] /usr/li
nathan r. hruby wrote
> On Sat 22 Jan 2005 Billy Davis wrote
>
> > We have just installed RHEL 3 on a Server with the following
> > configuration
> >
> > P4 3.4Gh
> > Intel 915GEV Mothertest
--
Taroon-list mailing list
Taroon-list@(protected)
http //www.redhat.com/mailman/listinfo/taroon-list
Je serai absent(e) du 24/01/2005 au 31/01/2005.
Je r??pondrai ?? votre message d??s mon retour.
Pour toutes questions concernant Linux veuillez contacter Pierre Gentile
(03.84.46.96.82We are using Samba to share out printers configured using Cups on a RHEL
3 Update 4 server with both Samba and Cups running on the same server.
We have a problem where after some time (sometimes aMy RHEL3/ELu4 system appears to be confused about the number of CPUs it
should be running.
The first CPU is detected at boot time (naturally) but dmesg throws an
error message from smpboot (see On Sun 23 Jan 2005 Tom Diehl wrote
> Hi all
>
> Can someone please look at the log entries below and tell me what is going
> on? I suspect the disk is on its way out but I would like anotheHi all
Can someone please look at the log entries below and tell me what is going
on? I suspect the disk is on its way out but I would like another opinion.
Jan 22 04 19 49 marge kernel hdc We have just installed RHEL 3 on a Server with the following configuration
P4 3.4Gh
Intel 915GEV Motherboard
Dual 73Gb U320 SCSI 10k rpm disks
1Gb of dual chanel DDR2 533Mhz memory (matched pTry also ethtool eht0 - which will show you the nic settings as shown
below and let you change them.
You want to be sure that both the switch and the nic are set to
autonegotiate or hard ffullI don 't think this is the case I have seen *many* cisco switches (and
other gear too) that use 10/Half and they are switches that handle
10/100/1000 speeds. I don 't think duplex and speed go toget |
|
|
