Hi all,

I was trying to clone my LCD display to VGA. HDMI and S-Video output.
I was succesful with the VGA though i couldn't manage to get anything
from my tries to HDMI and S-Video. What i did was the usual things:

I check the xrandr -q output and then tried to clone the display as

xrandr --output LVDS --mode 1024x768 --output TMDS-1 --mode 1024x768

The HDMI devise is flickered and i thought i will see my LCD screen
but it went to blank screen again. I tried different resolutions but
this time it never flickered.

At the S-Video, i even didn't see any flickering. So i may be missing
something.

For the HDMI part, if i use arandr and disable LVDS and enable TMDS-1
with a suitable resolution it worked. But the same approach didn't
work for S-Video. So there may be something about xorg settings that i
should fix. I played the xorg so i didn't check the current situation.
I added my xorg and lspci output.

--
Oğuz Yarımtepe

00:00.0 Host bridge: Intel Corporation Mobile PM965/GM965/GL960 Memory Controller Hub (rev 03)
 Subsystem: Unknown device 1a46:1402
 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
 Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
 Latency: 0
 Capabilities: [e0] Vendor Specific Information

00:02.0 VGA compatible controller: Intel Corporation Mobile GM965/GL960 Integrated Graphics Controller (rev 03) (prog-if 00 [VGA controller])
 Subsystem: Unknown device 1a46:1402
 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
 Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
 Latency: 0
 Interrupt: pin A routed to IRQ 11
 Region 0: Memory at 33000000 (64-bit, non-prefetchable) [size=1M]
 Region 2: Memory at 20000000 (64-bit, prefetchable) [size=256M]
 Region 4: I/O ports at 4110 [size=8]
 Capabilities: [90] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable-
   Address: 00000000 Data: 0000
 Capabilities: [d0] Power Management version 3
   Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
   Status: D0 PME-Enable- DSel=0 DScale=0 PME-
   Bridge: PM- B3+

00:02.1 Display controller: Intel Corporation Mobile GM965/GL960 Integrated Graphics Controller (rev 03)
 Subsystem: Unknown device 1a46:1402
 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
 Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
 Latency: 0
 Region 0: Memory at 33100000 (64-bit, non-prefetchable) [size=1M]
 Capabilities: [d0] Power Management version 3
   Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
   Status: D0 PME-Enable- DSel=0 DScale=0 PME-
   Bridge: PM- B3+

00:1a.0 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #4 (rev 03) (prog-if 00 [UHCI])
 Subsystem: Unknown device 1a46:1402
 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
 Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
 Latency: 0
 Interrupt: pin A routed to IRQ 17
 Region 4: I/O ports at 40c0 [size=32]

00:1a.1 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #5 (rev 03) (prog-if 00 [UHCI])
 Subsystem: Unknown device 1a46:1402
 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
 Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
 Latency: 0
 Interrupt: pin B routed to IRQ 16
 Region 4: I/O ports at 40a0 [size=32]

00:1a.7 USB Controller: Intel Corporation 82801H (ICH8 Family) USB2 EHCI Controller #2 (rev 03) (prog-if 20 [EHCI])
 Subsystem: Unknown device 1a46:1402
 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
 Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
 Latency: 0
 Interrupt: pin C routed to IRQ 20
 Region 0: Memory at 36404c00 (32-bit, non-prefetchable) [size=1K]
 Capabilities: [50] Power Management version 2
   Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
   Status: D0 PME-Enable- DSel=0 DScale=0 PME-
 Capabilities: [58] Debug port

00:1b.0 Audio device: Intel Corporation 82801H (ICH8 Family) HD Audio Controller (rev 03)
 Subsystem: Unknown device 1a46:1402
 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
 Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
 Latency: 0
 Interrupt: pin A routed to IRQ 21
 Region 0: Memory at 36400000 (64-bit, non-prefetchable) [size=16K]
 Capabilities: [50] Power Management version 2
   Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
   Status: D0 PME-Enable- DSel=0 DScale=0 PME-
 Capabilities: [60] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable-
   Address: 0000000000000000 Data: 0000
 Capabilities: [70] Express Unknown type IRQ 0
   Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
   Device: Latency L0s <64ns, L1 <1us
   Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
   Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
   Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
   Link: Supported Speed unknown, Width x0, ASPM unknown, Port 0
   Link: Latency L0s <64ns, L1 <1us
   Link: ASPM Disabled CommClk- ExtSynch-
   Link: Speed unknown, Width x0

00:1c.0 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 1 (rev 03) (prog-if 00 [Normal decode])
 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
 Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
 Latency: 0
 Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
 I/O behind bridge: 00003000-00003fff
 Memory behind bridge: 35300000-363fffff
 Prefetchable memory behind bridge: 0000000030000000-0000000030ffffff
 Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
 BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
 Capabilities: [40] Express Root Port (Slot+) IRQ 0
   Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
   Device: Latency L0s unlimited, L1 unlimited
   Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
   Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
   Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
   Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 1
   Link: Latency L0s <1us, L1 <4us
   Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
   Link: Speed 2.5Gb/s, Width x1
   Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug+ Surpise+
   Slot: Number 0, PowerLimit 6.500000
   Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
   Slot: AttnInd Unknown, PwrInd Unknown, Power-
   Root: Correctable- Non-Fatal- Fatal- PME-
 Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable+
   Address: fee0300c Data: 41b9
 Capabilities: [90] Subsystem: Gammagraphx, Inc. Unknown device 0000
 Capabilities: [a0] Power Management version 2
   Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
   Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:1c.1 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 2 (rev 03) (prog-if 00 [Normal decode])
 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
 Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
 Latency: 0
 Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
 I/O behind bridge: 00002000-00002fff
 Memory behind bridge: 34300000-352fffff
 Prefetchable memory behind bridge: 0000000031000000-0000000031ffffff
 Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
 BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
 Capabilities: [40] Express Root Port (Slot+) IRQ 0
   Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
   Device: Latency L0s unlimited, L1 unlimited
   Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
   Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
   Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
   Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 2
   Link: Latency L0s <1us, L1 <4us
   Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
   Link: Speed 2.5Gb/s, Width x0
   Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug+ Surpise+
   Slot: Number 1, PowerLimit 6.500000
   Slot: Enabled AtnBtn+ PwrFlt- MRL- PresDet+ CmdCplt- HPIrq-
   Slot: AttnInd Unknown, PwrInd Unknown, Power-
   Root: Correctable- Non-Fatal- Fatal- PME-
 Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable+
   Address: fee0300c Data: 41c1
 Capabilities: [90] Subsystem: Gammagraphx, Inc. Unknown device 0000
 Capabilities: [a0] Power Management version 2
   Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
   Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:1c.5 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 6 (rev 03) (prog-if 00 [Normal decode])
 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
 Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
 Latency: 0
 Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
 I/O behind bridge: 00001000-00001fff
 Memory behind bridge: 33300000-342fffff
 Prefetchable memory behind bridge: 0000000032000000-0000000032ffffff
 Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
 BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
 Capabilities: [40] Express Root Port (Slot+) IRQ 0
   Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
   Device: Latency L0s unlimited, L1 unlimited
   Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
   Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
   Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
   Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 6
   Link: Latency L0s <1us, L1 <4us
   Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
   Link: Speed 2.5Gb/s, Width x0
   Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug+ Surpise+
   Slot: Number 5, PowerLimit 6.500000
   Slot: Enabled AtnBtn+ PwrFlt- MRL- PresDet+ CmdCplt- HPIrq-
   Slot: AttnInd Unknown, PwrInd Unknown, Power-
   Root: Correctable- Non-Fatal- Fatal- PME-
 Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable+
   Address: fee0300c Data: 41c9
 Capabilities: [90] Subsystem: Gammagraphx, Inc. Unknown device 0000
 Capabilities: [a0] Power Management version 2
   Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
   Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:1d.0 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #1 (rev 03) (prog-if 00 [UHCI])
 Subsystem: Unknown device 1a46:1402
 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
 Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
 Latency: 0
 Interrupt: pin A routed to IRQ 18
 Region 4: I/O ports at 4080 [size=32]

00:1d.1 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #2 (rev 03) (prog-if 00 [UHCI])
 Subsystem: Unknown device 1a46:1402
 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
 Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
 Latency: 0
 Interrupt: pin B routed to IRQ 19
 Region 4: I/O ports at 4060 [size=32]

00:1d.2 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #3 (rev 03) (prog-if 00 [UHCI])
 Subsystem: Unknown device 1a46:1402
 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
 Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
 Latency: 0
 Interrupt: pin C routed to IRQ 20
 Region 4: I/O ports at 4040 [size=32]

00:1d.7 USB Controller: Intel Corporation 82801H (ICH8 Family) USB2 EHCI Controller #1 (rev 03) (prog-if 20 [EHCI])
 Subsystem: Unknown device 1a46:1402
 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
 Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
 Latency: 0
 Interrupt: pin A routed to IRQ 18
 Region 0: Memory at 36404800 (32-bit, non-prefetchable) [size=1K]
 Capabilities: [50] Power Management version 2
   Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
   Status: D0 PME-Enable- DSel=0 DScale=0 PME+
 Capabilities: [58] Debug port

00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev f3) (prog-if 01 [Subtractive decode])
 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
 Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
 Latency: 0
 Bus: primary=00, secondary=04, subordinate=04, sec-latency=32
 I/O behind bridge: 0000f000-00000fff
 Memory behind bridge: 33200000-332fffff
 Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff
 Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR+
 BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
 Capabilities: [50] Subsystem: Unknown device 1a46:1402

00:1f.0 ISA bridge: Intel Corporation 82801HEM (ICH8M) LPC Interface Controller (rev 03)
 Subsystem: Unknown device 1a46:1402
 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
 Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
 Latency: 0
 Capabilities: [e0] Vendor Specific Information

00:1f.1 IDE interface: Intel Corporation 82801HBM/HEM (ICH8M/ICH8M-E) IDE Controller (rev 03) (prog-if 8a [Master SecP PriP])
 Subsystem: Unknown device 1a46:1402
 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
 Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
 Latency: 0
 Interrupt: pin B routed to IRQ 17
 Region 0: I/O ports at 01f0 [size=8]
 Region 1: I/O ports at 03f4 [size=1]
 Region 2: I/O ports at 0170 [size=8]
 Region 3: I/O ports at 0374 [size=1]
 Region 4: I/O ports at 40e0 [size=16]

00:1f.2 SATA controller: Intel Corporation 82801HBM/HEM (ICH8M/ICH8M-E) SATA AHCI Controller (rev 03) (prog-if 01 [AHCI 1.0])
 Subsystem: Unknown device 1a46:1402
 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
 Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
 Latency: 0
 Interrupt: pin C routed to IRQ 220
 Region 0: I/O ports at 40f8 [size=8]
 Region 1: I/O ports at 411c [size=4]
 Region 2: I/O ports at 40f0 [size=8]
 Region 3: I/O ports at 4118 [size=4]
 Region 4: I/O ports at 4020 [size=32]
 Region 5: Memory at 36404000 (32-bit, non-prefetchable) [size=2K]
 Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/2 Enable+
   Address: fee0300c Data: 41e9
 Capabilities: [70] Power Management version 3
   Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold-)
   Status: D0 PME-Enable- DSel=0 DScale=0 PME-
 Capabilities: [a8] #12 [0010]

00:1f.3 SMBus: Intel Corporation 82801H (ICH8 Family) SMBus Controller (rev 03)
 Subsystem: Unknown device 1a46:1402
 Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
 Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
 Interrupt: pin D routed to IRQ 11
 Region 0: Memory at 36405000 (32-bit, non-prefetchable) [size=256]
 Region 4: I/O ports at 4000 [size=32]

01:00.0 Network controller: Intel Corporation PRO/Wireless 4965 AG or AGN Network Connection (rev 61)
 Subsystem: Intel Corporation Unknown device 1101
 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
 Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
 Latency: 0
 Interrupt: pin A routed to IRQ 219
 Region 0: Memory at 35300000 (64-bit, non-prefetchable) [size=8K]
 Capabilities: [c8] Power Management version 3
   Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
   Status: D0 PME-Enable- DSel=0 DScale=0 PME-
 Capabilities: [d0] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable+
   Address: 00000000fee0300c Data: 4132
 Capabilities: [e0] Express Endpoint IRQ 0
   Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
   Device: Latency L0s <512ns, L1 unlimited
   Device: AtnBtn- AtnInd- PwrInd-
   Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
   Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
   Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
   Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 0
   Link: Latency L0s <128ns, L1 <64us
   Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
   Link: Speed 2.5Gb/s, Width x1

04:02.0 FireWire (IEEE 1394): O2 Micro, Inc. Firewire (IEEE 1394) (rev 02) (prog-if 10 [OHCI])
 Subsystem: Unknown device 1a46:1402
 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
 Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
 Latency: 64
 Interrupt: pin A routed to IRQ 17
 Region 0: Memory at 33201000 (32-bit, non-prefetchable) [size=4K]
 Region 1: Memory at 33202000 (32-bit, non-prefetchable) [size=2K]
 Capabilities: [60] Power Management version 2
   Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
   Status: D0 PME-Enable- DSel=0 DScale=0 PME+

04:02.2 SD Host controller: O2 Micro, Inc. Integrated MMC/SD Controller (rev 01)
 Subsystem: Unknown device 1a46:1402
 Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
 Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR-
 Interrupt: pin A routed to IRQ 17
 Region 0: Memory at 33202800 (32-bit, non-prefetchable) [size=256]
 Capabilities: [a0] Power Management version 2
   Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
   Status: D0 PME-Enable- DSel=0 DScale=0 PME-

04:02.3 Mass storage controller: O2 Micro, Inc. Integrated MS/xD Controller (rev 01)
 Subsystem: Unknown device 1a46:1402
 Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
 Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR-
 Interrupt: pin A routed to IRQ 11
 Region 0: Memory at 33200000 (32-bit, non-prefetchable) [size=4K]
 Capabilities: [a0] Power Management version 2
   Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
   Status: D0 PME-Enable- DSel=0 DScale=0 PME-

--
ubuntu-users mailing list
ubuntu-users@(protected)
Modify settings or unsubscribe at: https://lists.ubuntu.com/mailman/listinfo/ubuntu-users