Luke S Crawford wrote:
> carlopmart <carlopmart@(protected):
>>>> When I try to copy a 465MB's or 650MB's file to domU, md5sum is
>>>> ok. But when I try to copy a 1GB file or more, md5sums are
>>>> wrong. Same result if I try to copy from domU. for example:
> ...
>> Please any hints?? I need to deploy this system on a production
>> environment with xen or with vmware server ...
>
> I can't reproduce the problem; several things to check:
>
> 1. ram. your problem could be caused by funky ram. run memtest86.
>
> 2. funky swap. run dmesg in the dom0. do you see funky problems related
> to disk? run smartctl and see if your disks are dying.
>
> Of course both of those things should also cause periodic swaps, but especially
> if you don't use ECC ram, and you normally use less ram than you are using
> with virtualization, setting up virtualization could cause to to use funky ram
> that would otherwise be idle.
>
> another thing to look at is dmesg in the DomU and see if there are
> any interesting messages.
>
> Also, The md5sum is wrong,but is the file size about right?
>
>

Thanks Luke for your responses. My answers:

1) memtest86 doesn't reports any error with ram.
2) when I try to start smartd i see these errors:

SCSI device sda: drive cache: write back
ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
ata1.00: cmd b0/da:00:00:4f:c2/00:00:00:00:00/00 tag 0 cdb 0x0 data 0
      res 51/04:00:80:00:00/00:00:00:00:00/00 Emask 0x1 (device error)
ata1.00: Host Protected Area detected:
     current size: 312579695 sectors
     native size: 312581808 sectors
ata1.00: Host Protected Area detected:
     current size: 312579695 sectors
     native size: 312581808 sectors
ata1.00: configured for UDMA/133
ata1: EH complete

3) file size are ok, only md5sums are wrong. But If I try to execute,
decompress, mount or I will try another operation to any file, all fails ...

I have attached dmesg from dom0 and domU

--
CL Martinez
carlopmart {at} gmail {d0t} com

Bootdata ok (command line is ro root=/dev/xvmvol/rootvol quiet)
Linux version 2.6.18-53.1.14.el5xen (brewbuilder@(protected)
BIOS-provided physical RAM map:
Xen: 0000000000000000 - 00000000b4fe0000 (usable)
On node 0 totalpages: 741344
DMA zone: 741344 pages, LIFO batch:31
DMI 2.3 present.
ACPI: RSDP (v000 MSTEST                     ) @ 0x00000000000f6cd0
ACPI: RSDT (v001 MSTEST TESTONLY 0x42302e31 AWRD 0x01010101) @ 0x00000000bfff3040
ACPI: FADT (v001 MSTEST TESTONLY 0x42302e31 AWRD 0x01010101) @ 0x00000000bfff30c0
ACPI: SLIC (v001 MSTEST TESTONLY 0x42302e31 AWRD 0x01010101) @ 0x00000000bfff77c0
ACPI: MCFG (v001 MSTEST TESTONLY 0x42302e31 AWRD 0x01010101) @ 0x00000000bfff7980
ACPI: MADT (v001 MSTEST TESTONLY 0x42302e31 AWRD 0x01010101) @ 0x00000000bfff76c0
ACPI: SSDT (v001 PmRef Cpu0Ist 0x00003000 INTL 0x20040311) @ 0x00000000bfff7a00
ACPI: SSDT (v001 PmRef   CpuPm 0x00003000 INTL 0x20040311) @ 0x00000000bfff7e90
ACPI: DSDT (v001 MSTEST AWRDACPI 0x00001000 MSFT 0x0100000c) @ 0x0000000000000000
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] disabled)
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x03] disabled)
ACPI: LAPIC_NMI (acpi_id[0x00] dfl dfl lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] dfl dfl lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x02] dfl dfl lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x03] dfl dfl lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: INT_SRC_OVR (bus 0 bus_irq 14 global_irq 14 high edge)
ACPI: INT_SRC_OVR (bus 0 bus_irq 15 global_irq 15 high edge)
ACPI: IRQ9 used by override.
ACPI: IRQ14 used by override.
ACPI: IRQ15 used by override.
Setting APIC routing to xen
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at c2000000 (gap: c0000000:20000000)
Built 1 zonelists. Total pages: 741344
Kernel command line: ro root=/dev/xvmvol/rootvol quiet
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 32768 bytes)
Xen reported: 3213.968 MHz processor.
Console: colour VGA+ 80x25
Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
Software IO TLB enabled:
Aperture:   64 megabytes
Kernel range: 0xffff880004d0c000 - 0xffff880008d0c000
PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
Memory: 2819072k/2965376k available (2358k kernel code, 137484k reserved, 1325k data, 172k init)
Calibrating delay using timer specific routine.. 8039.58 BogoMIPS (lpj=16079170)
Security Framework v1.0.0 initialized
SELinux: Initializing.
SELinux: Starting in permissive mode
selinux_register_security: Registering secondary module capability
Capability LSM initialized as secondary
Mount-cache hash table entries: 256
CPU: Trace cache: 12K uops, L1 D cache: 16K
CPU: L2 cache: 2048K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
(SMP-)alternatives turned off
ACPI: Core revision 20060707
Brought up 2 CPUs
sizeof(vma)=168 bytes
sizeof(page)=56 bytes
sizeof(inode)=560 bytes
sizeof(dentry)=216 bytes
sizeof(ext3inode)=760 bytes
sizeof(buffer_head)=96 bytes
sizeof(skbuff)=240 bytes
Initializing CPU#1
migration_cost=1780
checking if image is initramfs... it is
Grant table initialized
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: BIOS Bug: MCFG area at e0000000 is not E820-reserved
PCI: Not using MMCONFIG.
PCI: Using configuration type 1
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
Boot video device is 0000:01:00.0
PCI: Transparent bridge - 0000:00:12.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT]
ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNK2] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK3] (IRQs 3 4 *5 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNK4] (IRQs 3 4 5 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNK5] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LUBA] (IRQs 3 4 5 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LUBB] (IRQs 3 4 5 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LMAC] (IRQs 3 4 5 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LACI] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LMCI] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LSMB] (IRQs 3 4 *5 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LUB2] (IRQs 3 4 *5 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LIDE] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LSID] (IRQs 3 4 5 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LFID] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LPCA] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [APC1] (IRQs 16) *0, disabled.
ACPI: PCI Interrupt Link [APC2] (IRQs 17) *0, disabled.
ACPI: PCI Interrupt Link [APC3] (IRQs 18) *0, disabled.
ACPI: PCI Interrupt Link [APC4] (IRQs 19) *0, disabled.
ACPI: PCI Interrupt Link [APC5] (IRQs *16), disabled.
ACPI: PCI Interrupt Link [APCF] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCG] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCH] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCJ] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCK] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCS] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCL] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APSI] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APSJ] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCP] (IRQs 20 21 22 23) *0, disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 15 devices
xen_mem: Initialising balloon driver.
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
NetLabel: Initializing
NetLabel: domain hash size = 128
NetLabel: protocols = UNLABELED CIPSOv4
NetLabel: unlabeled traffic allowed by default
pnp: 00:01: ioport range 0x1400-0x147f could not be reserved
pnp: 00:01: ioport range 0x1480-0x14ff has been reserved
pnp: 00:01: ioport range 0x1800-0x187f has been reserved
pnp: 00:01: ioport range 0x1880-0x18ff could not be reserved
pnp: 00:01: ioport range 0x1c00-0x1c7f has been reserved
pnp: 00:01: ioport range 0x1c80-0x1cff has been reserved
PCI: Bridge: 0000:00:02.0
IO window: disabled.
MEM window: d0000000-d2ffffff
PREFETCH window: c0000000-cfffffff
PCI: Bridge: 0000:00:12.0
IO window: b000-bfff
MEM window: d3000000-d4ffffff
PREFETCH window: d5100000-d51fffff
PCI: Setting latency timer of device 0000:00:02.0 to 64
PCI: Setting latency timer of device 0000:00:12.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 131072 (order: 8, 1048576 bytes)
TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
TCP: Hash tables configured (established 262144 bind 65536)
TCP reno registered
audit: initializing netlink socket (disabled)
audit(1208337416.272:1): initialized
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
SELinux: Registering netfilter hooks
Initializing Cryptographic API
ksign: Installing public key data
Loading keyring
- Added public key E192A392652F9718
- User ID: Red Hat, Inc. (Kernel Module GPG key)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
PCI: Setting latency timer of device 0000:00:02.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:02.0:pcie00]
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
ACPI (exconfig-0455): Dynamic SSDT Load - OemId [ PmRef] OemTableId [ Cpu1Ist] [20060707]
ACPI Exception (acpi_processor-0681): AE_NOT_FOUND, Processor Device is not present [20060707]
ACPI: Getting cpuindex for acpiid 0x2
ACPI Exception (acpi_processor-0681): AE_NOT_FOUND, Processor Device is not present [20060707]
ACPI: Getting cpuindex for acpiid 0x3
Real Time Clock Driver v1.12ac
Non-volatile memory driver v1.2
Linux agpgart interface v0.101 (c) Dave Jones
RAMDISK driver initialized: 16 RAM disks of 16384K size 4096 blocksize
Xen virtual console successfully installed as ttyS0
Event-channel device installed.
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
NFORCE-MCP04: IDE controller at PCI slot 0000:00:0f.0
NFORCE-MCP04: chipset revision 242
NFORCE-MCP04: not 100% native mode: will probe irqs later
NFORCE-MCP04: 0000:00:0f.0 (rev f2) UDMA133 controller
  ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:DMA
  ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:DMA
Probing IDE interface ide0...
hda: SONY DVD-ROM DDU1615, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
Probing IDE interface ide1...
ide-floppy driver 0.99.newide
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 4.39
TCP bic registered
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
Write protecting the kernel read-only data: 445k
input: AT Translated Set 2 keyboard as /class/input/input0
USB Universal Host Controller Interface driver v3.0
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ACPI: PCI Interrupt Link [APCF] enabled at IRQ 23
GSI 16 sharing vector 0xA8 and IRQ 16
ACPI: PCI Interrupt 0000:00:0b.0[A] -> Link [APCF] -> GSI 23 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:0b.0 to 64
ohci_hcd 0000:00:0b.0: OHCI Host Controller
ohci_hcd 0000:00:0b.0: new USB bus registered, assigned bus number 1
ohci_hcd 0000:00:0b.0: irq 16, io mem 0xd5004000
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 5 ports detected
ACPI: PCI Interrupt Link [APCG] enabled at IRQ 22
GSI 17 sharing vector 0xB0 and IRQ 17
ACPI: PCI Interrupt 0000:00:0b.1[B] -> Link [APCG] -> GSI 22 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:0b.1 to 64
ohci_hcd 0000:00:0b.1: OHCI Host Controller
ohci_hcd 0000:00:0b.1: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:0b.1: irq 17, io mem 0xd5000000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 5 ports detected
ACPI: PCI Interrupt Link [APCL] enabled at IRQ 21
GSI 18 sharing vector 0xB8 and IRQ 18
ACPI: PCI Interrupt 0000:00:0b.2[C] -> Link [APCL] -> GSI 21 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:0b.2 to 64
ehci_hcd 0000:00:0b.2: EHCI Host Controller
ehci_hcd 0000:00:0b.2: new USB bus registered, assigned bus number 3
ehci_hcd 0000:00:0b.2: debug port 1
PCI: cache line size of 128 is not supported by device 0000:00:0b.2
ehci_hcd 0000:00:0b.2: irq 18, io mem 0xd5001000
ehci_hcd 0000:00:0b.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 10 ports detected
SCSI subsystem initialized
libata version 2.21 loaded.
sata_nv 0000:00:10.0: version 3.4
ACPI: PCI Interrupt Link [APSI] enabled at IRQ 20
GSI 19 sharing vector 0xC0 and IRQ 19
ACPI: PCI Interrupt 0000:00:10.0[A] -> Link [APSI] -> GSI 20 (level, low) -> IRQ 19
sata_nv 0000:00:10.0: Using ADMA mode
PCI: Setting latency timer of device 0000:00:10.0 to 64
scsi0 : sata_nv
scsi1 : sata_nv
ata1: SATA max UDMA/133 cmd 0xffffc20000026480 ctl 0xffffc200000264a0 bmdma 0x000000000001dc00 irq 19
ata2: SATA max UDMA/133 cmd 0xffffc20000026580 ctl 0xffffc200000265a0 bmdma 0x000000000001dc08 irq 19
input: ImPS/2 Generic Wheel Mouse as /class/input/input1
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: Host Protected Area detected:
 current size: 312579695 sectors
 native size: 312581808 sectors
ata1.00: ATA-7: Maxtor 6V160E0, VA111900, max UDMA/133
ata1.00: 312579695 sectors, multi 16: LBA48 NCQ (depth 31/32)
ata1.00: Host Protected Area detected:
 current size: 312579695 sectors
 native size: 312581808 sectors
ata1.00: configured for UDMA/133
ata2: SATA link down (SStatus 0 SControl 300)
Vendor: ATA     Model: Maxtor 6V160E0   Rev: VA11
Type:  Direct-Access               ANSI SCSI revision: 05
ata1: bounce limit 0xFFFFFFFFFFFFFFFF, segment boundary 0xFFFFFFFF, hw segs 61
SCSI device sda: 312579695 512-byte hdwr sectors (160041 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
SCSI device sda: 312579695 512-byte hdwr sectors (160041 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
sda: sda1 sda2 sda3
sd 0:0:0:0: Attached scsi disk sda
device-mapper: ioctl: 4.11.0-ioctl (2006-09-14) initialised: dm-devel@(protected)
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
SELinux: Disabled at runtime.
SELinux: Unregistering netfilter hooks
audit(1208337423.520:2): selinux=0 auid=4294967295
hda: ATAPI 40X DVD-ROM drive, 1725kB Cache, UDMA(66)
Uniform CD-ROM driver Revision: 3.20
i2c_adapter i2c-0: nForce2 SMBus adapter at 0x700
i2c_adapter i2c-1: nForce2 SMBus adapter at 0x900
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
8250_pnp: Unknown symbol serial8250_unregister_port
8250_pnp: Unknown symbol serial8250_register_port
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.60.
ACPI: PCI Interrupt Link [APCH] enabled at IRQ 23
ACPI: PCI Interrupt 0000:00:0e.0[A] -> Link [APCH] -> GSI 23 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:0e.0 to 64
forcedeth: using HIGHDMA
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
input: PC Speaker as /class/input/input2
8139too Fast Ethernet driver 0.9.27
8250_pnp: Unknown symbol serial8250_unregister_port
8250_pnp: Unknown symbol serial8250_register_port
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
sd 0:0:0:0: Attached scsi generic sg0 type 0
eth0: forcedeth.c: subsystem: 01458:e000 bound to 0000:00:0e.0
ACPI: PCI Interrupt Link [APC3] enabled at IRQ 18
GSI 20 sharing vector 0xC8 and IRQ 20
ACPI: PCI Interrupt 0000:02:06.0[A] -> Link [APC3] -> GSI 18 (level, low) -> IRQ 20
eth1: RealTek RTL8139 at 0xffffc2000002a000, 00:80:5a:4a:2b:fc, IRQ 20
eth1: Identified 8139 chip type 'RTL-8100B/8139D'
ACPI: PCI Interrupt Link [APC4] enabled at IRQ 19
GSI 21 sharing vector 0xD0 and IRQ 21
ACPI: PCI Interrupt 0000:02:07.0[A] -> Link [APC4] -> GSI 19 (level, low) -> IRQ 21
eth2: RealTek RTL8139 at 0xffffc20000032000, 00:08:54:4c:55:60, IRQ 21
eth2: Identified 8139 chip type 'RTL-8100B/8139D'
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
8139cp: 10/100 PCI Ethernet driver v1.2 (Mar 22, 2004)
lp0: using parport0 (interrupt-driven).
lp0: console ready
ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [PWRB]
ibm_acpi: ec object not found
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
device-mapper: multipath: version 1.0.5 loaded
EXT3 FS on dm-0, internal journal
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Adding 3148732k swap on /dev/sda2. Priority:-1 extents:1 across:3148732k
Bridge firewalling registered
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
eth0: Promiscuous mode enabled.
device eth0 entered promiscuous mode
audit(1208337430.519:3): dev=eth0 prom=256 old_prom=0 auid=4294967295
eth1: link up, 100Mbps, full-duplex, lpa 0x45E1
eth1: Promiscuous mode enabled.
device eth1 entered promiscuous mode
audit(1208337430.683:4): dev=eth1 prom=256 old_prom=0 auid=4294967295
eth2: no link during initialization.
device eth2 entered promiscuous mode
audit(1208337430.887:5): dev=eth2 prom=256 old_prom=0 auid=4294967295
xenbr0: port 1(eth0) entering learning state
xenbr0: topology change detected, propagating
xenbr0: port 1(eth0) entering forwarding state
xenbr1: port 1(eth1) entering learning state
xenbr1: topology change detected, propagating
xenbr1: port 1(eth1) entering forwarding state
device srvauth_if entered promiscuous mode
audit(1208337453.204:6): dev=srvauth_if prom=256 old_prom=0 auid=4294967295
blkback: ring-ref 8, event-channel 8, protocol 1 (x86_64-abi)
xenbr0: port 2(srvauth_if) entering learning state
xenbr0: topology change detected, propagating
xenbr0: port 2(srvauth_if) entering forwarding state

Bootdata ok (command line is ro root=/dev/sysvol/rootvol quiet)
Linux version 2.6.18-53.1.14.el5xen (brewbuilder@(protected)
BIOS-provided physical RAM map:
Xen: 0000000000000000 - 0000000030800000 (usable)
On node 0 totalpages: 198656
DMA zone: 198656 pages, LIFO batch:31
No mptable found.
Built 1 zonelists. Total pages: 198656
Kernel command line: ro root=/dev/sysvol/rootvol quiet
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 32768 bytes)
Xen reported: 3213.848 MHz processor.
Console: colour dummy device 80x25
Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
Inode-cache hash table entries: 65536 (order: 7, 524288 bytes)
Software IO TLB disabled
Memory: 758016k/794624k available (2358k kernel code, 27692k reserved, 1325k data, 172k init)
Calibrating delay using timer specific routine.. 8038.96 BogoMIPS (lpj=16077932)
Security Framework v1.0.0 initialized
SELinux: Initializing.
SELinux: Starting in permissive mode
selinux_register_security: Registering secondary module capability
Capability LSM initialized as secondary
Mount-cache hash table entries: 256
CPU: Trace cache: 12K uops, L1 D cache: 16K
CPU: L2 cache: 2048K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
(SMP-)alternatives turned off
Brought up 1 CPUs
sizeof(vma)=168 bytes
sizeof(page)=56 bytes
sizeof(inode)=560 bytes
sizeof(dentry)=216 bytes
sizeof(ext3inode)=760 bytes
sizeof(buffer_head)=96 bytes
sizeof(skbuff)=240 bytes
checking if image is initramfs... it is
Grant table initialized
NET: Registered protocol family 16
ACPI Exception (utmutex-0262): AE_BAD_PARAMETER, Thread DB57A0 could not acquire Mutex [2] [20060707]
ACPI Exception (utmutex-0262): AE_BAD_PARAMETER, Thread DB57A0 could not acquire Mutex [2] [20060707]
Brought up 1 CPUs
PCI: setting up Xen PCI frontend stub
ACPI: Interpreter disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI: disabled
xen_mem: Initialising balloon driver.
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: System does not support PCI
PCI: System does not support PCI
NetLabel: Initializing
NetLabel: domain hash size = 128
NetLabel: protocols = UNLABELED CIPSOv4
NetLabel: unlabeled traffic allowed by default
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 6, 262144 bytes)
TCP established hash table entries: 131072 (order: 9, 2097152 bytes)
TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
audit: initializing netlink socket (disabled)
audit(1208337453.611:1): initialized
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
SELinux: Registering netfilter hooks
Initializing Cryptographic API
ksign: Installing public key data
Loading keyring
- Added public key E192A392652F9718
- User ID: Red Hat, Inc. (Kernel Module GPG key)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
rtc: IRQ 8 is not free.
Non-volatile memory driver v1.2
Linux agpgart interface v0.101 (c) Dave Jones
RAMDISK driver initialized: 16 RAM disks of 16384K size 4096 blocksize
Xen virtual console successfully installed as xvc0
Event-channel device installed.
Console: switching to colour frame buffer device 100x37
input: Xen Virtual Keyboard/Mouse as /class/input/input0
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 50MHz system bus speed for PIO modes; override with idebus=xx
Probing IDE interface ide0...
Probing IDE interface ide1...
Probing IDE interface ide2...
Probing IDE interface ide3...
Probing IDE interface ide4...
Probing IDE interface ide5...
ide-floppy driver 0.99.newide
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
PNP: No PS/2 controller found. Probing ports directly.
i8042.c: No controller found.
mice: PS/2 mouse device common for all mice
md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 4.39
TCP bic registered
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
XENBUS: Device with no driver: device/vbd/51712
XENBUS: Device with no driver: device/vif/0
Write protecting the kernel read-only data: 445k
USB Universal Host Controller Interface driver v3.0
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
Registering block device major 202
xvda: xvda1 xvda2 xvda3
device-mapper: ioctl: 4.11.0-ioctl (2006-09-14) initialised: dm-devel@(protected)
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
SELinux: Disabled at runtime.
SELinux: Unregistering netfilter hooks
audit(1208337461.124:2): selinux=0 auid=4294967295
input: PC Speaker as /class/input/input1
Floppy drive(s): fd0 is unknown type 15 (usb?), fd1 is unknown type 15 (usb?)
Failed to obtain physical IRQ 6
floppy0: no floppy controllers found
lp: driver loaded but no devices found
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
device-mapper: multipath: version 1.0.5 loaded
EXT3 FS on dm-0, internal journal
kjournald starting. Commit interval 5 seconds
EXT3 FS on xvda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Adding 1574360k swap on /dev/xvda2. Priority:-1 extents:1 across:1574360k
netfront: Initialising virtual ethernet driver.
netfront: device eth0 has flipping receive path.

_______________________________________________
rhelv5-list mailing list
rhelv5-list@(protected)
https://www.redhat.com/mailman/listinfo/rhelv5-list