Author Login •
Post Reply
Professionaly, I deal with Proliant systems with Smartarrays ... which is
to say I deal very little with the hardware interface-level stuff, it just
always works. Personally I inherited this E6750 (Core 2 Duo) ASUS
motherboard and wanted thought I'd build a nice server for general use. I
added 4 SATA 250 Gb disc drives and after reading about the horrors &
failures of the cheapie Raid controllers, I decided to try Linux software raid.
I made Raid volumes for each drive pretty much the same size as I would an
ordinary drive, but all four drives. I then specified raid devices (md0
was /boot using Raid1 between drive 0 &1) md2 was /, likewise mirrored
between 0&1 while md3, 4 & 5 were RAID5 across all 4 drives. (so drives 2
&3 each had two wasted partitions and each drive also had a regular old
swap partition)
Anaconda installed Linux (RHEL4-U5-i386) and during final boot, I got a
message that Raid Superblocks weren't correctly written, but it came up &
ran fine. I gave it some file copying work to do while I was busy ... and
I came back 2 hours later to find Linux reporting that /home was now a
read-only file system (as was /usr & /var) and the system was, as they say,
dead as fried chicken.
Upon reboot, I got a message from every MD partition that there were not
enough available partitions for /usr /var & /home and that they each had 2
of 4 devices failed.
Repeated the steps above ... not correcting a single step ... got the same
results ->> that didn't surprise me, so I'm at least partially insane.
So far, web searching has yielded (1) Asus motherboards are bad (2)
Sata-nv drivers buggy (3) Sata disc drives evil (4) Forget about Raid on
/boot or / (5) Linux doesn't support sata or Raid very well until RHEL5
and the ubiquitous #6 .... with me on almost any project .... that I suck
as a technician, in way over my head, have so many knowledge gaps that I
skipped so many crucial steps that the only wonder is that the hardware did
not turn on me and try to electrocute me.
So now the questions:
(A) Anyone see an obvious, incorrectable flaw in the technology such as a
'known condition' given the situation? (trust me .. #6 is a universal
constant)
(B) Anyone suggest the step(s) that I missed that even a trained monkey
would have noticed (be honest, I can take it)
(C) If I just invested the $$ in an LSI logic or MSI (real hardware raid)
controller, would all these problems just vanish?
At 09:00 AM 2/11/2008, you wrote:
>Send redhat-list mailing list submissions to
> redhat-list@(protected)
>
>To subscribe or unsubscribe via the World Wide Web, visit
> https://www.redhat.com/mailman/listinfo/redhat-list
>or, via email, send a message with subject or body 'help' to
> redhat-list-request@(protected)
>
>You can reach the person managing the list at
> redhat-list-owner@(protected)
>
>When replying, please edit your Subject line so it is more specific
>than "Re: Contents of redhat-list digest..."
>
>
>Today's Topics:
>
> 1. Re:Why am I seeing this? ** portmap server not responding
> **? (Pankaj Batra)
> 2. how to make mirror of server on red hat 8.0 (Pankaj Batra)
> 3. Re: how to make mirror of server on red hat 8.0 (Romeo Theriault)
> 4. RE: Disk partitions and LVM limits (Tom Greaser)
> 5. RE: SSH Consent Banner (Mertens, Bram)
> 6. Keyboard layout problem in XEN virtual machine (Mertens, Bram)
> 7. "smbclient -L servername -N" not working (Margaret Doll)
> 8. RE: Disk partitions and LVM limits (Kirk Wight)
>
>
>----------------------------------------------------------------------
>
>Message: 1
>Date: Sun, 10 Feb 2008 18:24:06 +0000 (GMT)
>From: Pankaj Batra <batra786@(protected)>
>Subject: Re:Why am I seeing this? ** portmap server not responding
> **?
>To: redhat-list@(protected)
>Message-ID: <386145.84784.qm@(protected)>
>Content-Type: text/plain; charset=iso-8859-1
>
>Hi Ryan.
>
> ## Try stopping portmap and xinetd service and then unexporting the
> export files for that particular IP and then restart your server and then
> start the service ie portmap and xinetd.Check logs then.
>
> ## Please check the following file also /etc/fstab on both server and
> client.
>
>
> Best of Luck.
>
>
>redhat-list-request@(protected):
> Send redhat-list mailing list submissions to
>redhat-list@(protected)
>
>To subscribe or unsubscribe via the World Wide Web, visit
>https://www.redhat.com/mailman/listinfo/redhat-list
>or, via email, send a message with subject or body 'help' to
>redhat-list-request@(protected)
>
>You can reach the person managing the list at
>redhat-list-owner@(protected)
>
>When replying, please edit your Subject line so it is more specific
>than "Re: Contents of redhat-list digest..."
>
>
>Today's Topics:
>
>1. Disk partitions and LVM limits (Peter Blajev)
>2. Why am I seeing this? ** portmap server not responding **?
>(Ryan Golhar)
>3. RE: Disk partitions and LVM limits (Geofrey Rainey)
>
>
>----------------------------------------------------------------------
>
>Message: 1
>Date: Fri, 8 Feb 2008 10:58:56 -0800
>From: Peter Blajev
>
>Subject: Disk partitions and LVM limits
>To: Red Hat List
>Message-ID: <200802081058.56499.pblajev@(protected)>
>Content-Type: text/plain; charset="us-ascii"
>
>Hi,
>
>I've got a DAS DELL MD1000 with a bunch of SATA drives in RAID 5
>configuration
>with total space of 5.4TB. This box is attached to a CentOS5 system (kernel
>2.6.18-53.1.6.el5).
>
>Any idea how to make this space usable?
>Is there a limit how big a partition can be? What is the work around?
>Is there a limit how big a file system ca be?
>
>I've tried to partition it but no matter how bug partition I create fdisk
>spits out these messages on the console:
>---
>sdb: very big device. try to use READ CAPACITY(16).
>SCSI device sdb: 10248519680 512-byte hdwr sectors (5247242 MB)
>sdb: Write Protect is off
>---
>
>I decided to not partition the drive and use LVM but the physical volume
>stopped at 2TB.
>
>So, right now I can't use LVM because of this 2TB limit and I'm not sure if I
>partition the drive how good these partitions are because of the the message
>from fdisk.
>
>Any help or idea is highly appreciated.
>
>Thank you
>Peter
>
>
>
>------------------------------
>
>Message: 2
>Date: Fri, 08 Feb 2008 15:06:08 -0500
>From: Ryan Golhar
>Subject: Why am I seeing this? ** portmap server not responding **?
>To: General Red Hat Linux discussion list
>Message-ID: <47ACB630.2050905@(protected)>
>Content-Type: text/plain; charset=ISO-8859-1; format=flowed
>
>I have a server (RHEL 5) that makes 2 directories available to a bunch
>of clients via NFS. I keep seeing this particular message in the
>servers log:
>
>Feb 8 15:02:12 sapphire kernel: portmap: server 192.168.101.164 not
>responding, timed out
>
>The machine, 192.168.101.164 is a client machine that isn't even up at
>the moment. I remove the entry from /etc/exports for that machine and
>re-ran "exportfs -rv". I still see this message.
>
>The server isn't mounting any file system or anything from the client
>machine. Why would I see this message on the servers logs?
>
>Ryan
>
>
>
>
>------------------------------
>
>Message: 3
>Date: Sat, 9 Feb 2008 23:42:46 +1300
>From: "Geofrey Rainey"
>Subject: RE: Disk partitions and LVM limits
>To: "General Red Hat Linux discussion list"
>Message-ID:
>
>Content-Type: text/plain; charset="us-ascii"
>
>You could change the sizing of the 5.4TB logical partition into smaller
>logical partitions
>Of 2TB in size, make each of these a physical volume and add them to a
>volume group, then create a logical volume from that volume group.
>I don't know if this 2TB limit will affect this procedure though.
>
>-----Original Message-----
>From: redhat-list-bounces@(protected)
>[mailto:redhat-list-bounces@(protected)
>Sent: Saturday, 9 February 2008 7:59 a.m.
>To: Red Hat List
>Subject: Disk partitions and LVM limits
>
>Hi,
>
>I've got a DAS DELL MD1000 with a bunch of SATA drives in RAID 5
>configuration with total space of 5.4TB. This box is attached to a
>CentOS5 system (kernel 2.6.18-53.1.6.el5).
>
>Any idea how to make this space usable?
>Is there a limit how big a partition can be? What is the work around?
>Is there a limit how big a file system ca be?
>
>I've tried to partition it but no matter how bug partition I create
>fdisk spits out these messages on the console:
>---
>sdb: very big device. try to use READ CAPACITY(16).
>SCSI device sdb: 10248519680 512-byte hdwr sectors (5247242 MB)
>sdb: Write Protect is off
>---
>
>I decided to not partition the drive and use LVM but the physical volume
>stopped at 2TB.
>
>So, right now I can't use LVM because of this 2TB limit and I'm not sure
>if I partition the drive how good these partitions are because of the
>the message from fdisk.
>
>Any help or idea is highly appreciated.
>
>Thank you
>Peter
>
>--
>redhat-list mailing list
>unsubscribe mailto:redhat-list-request@(protected)
>https://www.redhat.com/mailman/listinfo/redhat-list
>==========================================================
>For more information on the Television New Zealand Group, visit us
>online at tvnz.co.nz
>==========================================================
>CAUTION: This e-mail and any attachment(s) contain information that
>is intended to be read only by the named recipient(s). This information
>is not to be used or stored by any other person and/or organisation.
>
>
>
>
>------------------------------
>
>__
>redhat-list mailing list
>Unsubscribe mailto:redhat-list-request@(protected)
>https://www.redhat.com/mailman/listinfo/redhat-list
>
>End of redhat-list Digest, Vol 48, Issue 8
>******************************************
>
>
>
>Pankaj Batra
>( TL ) iBilt Technologies Ltd.
>
>---------------------------------
> Now you can chat without downloading messenger. Click here to know how.
>
>------------------------------
>
>Message: 2
>Date: Sun, 10 Feb 2008 19:01:14 +0000 (GMT)
>From: Pankaj Batra <batra786@(protected)>
>Subject: how to make mirror of server on red hat 8.0
>To: redhat-list@(protected)
>Message-ID: <842539.17699.qm@(protected)>
>Content-Type: text/plain; charset=iso-8859-1
>
>Hi techies..
> Please can anyone guide me how to make mirror of
> server on red hat 8.0. I have IBM eseries server with RAID 5 configured
> with 4 SCSI drives.
> I wanna make to make mirror of it on similar server.
> So that at time of any kinde of crash I can use the mirror and data and
> time can be saved.
>
>
> Regards & Thanks.
>
>
>
>
>
>Pankaj Batra
>( TL ) iBilt Technologies Ltd.
>
>---------------------------------
> Forgot the famous last words? Access your message archive online. Click
> here.
>
>------------------------------
>
>Message: 3
>Date: Sun, 10 Feb 2008 16:28:35 -0500
>From: "Romeo Theriault" <romeotheriault@(protected)>
>Subject: Re: how to make mirror of server on red hat 8.0
>To: "General Red Hat Linux discussion list" <redhat-list@(protected)>
>Message-ID:
> <46cd475b0802101328p2618e2d2n4fdbd1b6789dbe0e@(protected)>
>Content-Type: text/plain; charset=ISO-8859-1
>
>These two have worked well for me in the past.
>
>clonezilla live - http://clonezilla.sourceforge.net/clonezilla-live/
>g4u - http://www.feyrer.de/g4u/
>
>Romeo
>
>On Feb 10, 2008 2:01 PM, Pankaj Batra <batra786@(protected):
>
> > Hi techies..
> > Please can anyone guide me how to make mirror of server
> > on red hat 8.0. I have IBM eseries server with RAID 5 configured with 4
> > SCSI drives.
> > I wanna make to make mirror of it on similar server.
> > So that at time of any kinde of crash I can use the mirror and data and
> > time can be saved.
> >
> >
> > Regards & Thanks.
> >
> >
> >
> >
> >
> > Pankaj Batra
> > ( TL ) iBilt Technologies Ltd.
> >
> > ---------------------------------
> > Forgot the famous last words? Access your message archive online. Click
> > here.
> > --
> > redhat-list mailing list
> > unsubscribe mailto:redhat-list-request@(protected)
> > https://www.redhat.com/mailman/listinfo/redhat-list
> >
>
>
>
>--
>Romeo Theriault
>System Administrator
>Information Technology Services
>Ph#: 207-561-3517
>Em@(protected)
>
>
>------------------------------
>
>Message: 4
>Date: Sun, 10 Feb 2008 17:05:49 -0500
>From: "Tom Greaser" <tgreaser@(protected)>
>Subject: RE: Disk partitions and LVM limits
>To: <redhat-list@(protected)>
>Message-ID: <47AF2EED.34C4.0040.3@(protected)>
>Content-Type: text/plain; charset=UTF-8
>
>If you man fdisk
>fdisk doesnât understand GUID Partition Table (GPT) and it is not
> designed for large partitions. In particular case use more
>advanced GNU
> parted(8).
>
>try parted and let use know if that works.. im coming up on a large BOD
>setup soon
>
>
>Message: 3
>Date: Sat, 9 Feb 2008 23:42:46 +1300
>From: "Geofrey Rainey" <Geofrey.Rainey@(protected)>
>Subject: RE: Disk partitions and LVM limits
>To: "General Red Hat Linux discussion list" <redhat-list@(protected)>
>Message-ID:
><FCFF2EC7A020964FBC98B17F17A88AC453D246@(protected)>
>Content-Type: text/plain; charset="us-ascii"
>
>You could change the sizing of the 5.4TB logical partition into smaller
>logical partitions
>Of 2TB in size, make each of these a physical volume and add them to a
>volume group, then create a logical volume from that volume group.
>I don't know if this 2TB limit will affect this procedure though.
>
>-----Original Message-----
>From: redhat-list-bounces@(protected)
>[mailto:redhat-list-bounces@(protected)
>Sent: Saturday, 9 February 2008 7:59 a.m.
>To: Red Hat List
>Subject: Disk partitions and LVM limits
>
>Hi,
>
>I've got a DAS DELL MD1000 with a bunch of SATA drives in RAID 5
>configuration with total space of 5.4TB. This box is attached to a
>CentOS5 system (kernel 2.6.18-53.1.6.el5).
>
>Any idea how to make this space usable?
>Is there a limit how big a partition can be? What is the work around?
>Is there a limit how big a file system ca be?
>
>I've tried to partition it but no matter how bug partition I create
>fdisk spits out these messages on the console:
>---
>sdb: very big device. try to use READ CAPACITY(16).
>SCSI device sdb: 10248519680 512-byte hdwr sectors (5247242 MB)
>sdb: Write Protect is off
>---
>
>I decided to not partition the drive and use LVM but the physical volume
>stopped at 2TB.
>
>So, right now I can't use LVM because of this 2TB limit and I'm not sure
>if I partition the drive how good these partitions are because of the
>the message from fdisk.
>
>Any help or idea is highly appreciated.
>
>Thank you
>Peter
>
>--
>redhat-list mailing list
>unsubscribe mailto:redhat-list-request@(protected)
>https://www.redhat.com/mailman/listinfo/redhat-list
>==========================================================
>For more information on the Television New Zealand Group, visit us
>online at tvnz.co.nz
>==========================================================
>CAUTION: This e-mail and any attachment(s) contain information that
>is intended to be read only by the named recipient(s). This information
>is not to be used or stored by any other person and/or organisation.
>
>
>
>
>------------------------------
>
>__
>redhat-list mailing list
>Unsubscribe mailto:redhat-list-request@(protected)
>https://www.redhat.com/mailman/listinfo/redhat-list
>
>End of redhat-list Digest, Vol 48, Issue 8
>******************************************
>
>
>
>------------------------------
>
>Message: 5
>Date: Mon, 11 Feb 2008 11:07:12 +0100
>From: "Mertens, Bram" <mertensb@(protected)>
>Subject: RE: SSH Consent Banner
>To: "General Red Hat Linux discussion list" <redhat-list@(protected)>
>Message-ID:
> <E4763D73EF6E4848853562C30CA5A9AF012791BE@(protected)>
>Content-Type: text/plain; charset="us-ascii"
>
>Doesn't pressing CTRL+C get you out of this? In that it stops
>processing the script but still lets you log in.
>
>Regards
>
>Bram
>
> >
>
>
>Mazda Motor Logistics Europe NV, Blaasveldstraat 162, B-2830 Willebroek
>VAT BE 406.024.281, RPR Mechelen, ING 310-0092504-52, IBAN : BE64 3100
>0925 0452, SWIFT : BBRUBEBB
>
>-----Original Message-----
> > From: redhat-list-bounces@(protected)
> > [mailto:redhat-list-bounces@(protected)
> > Sent: zaterdag 2 februari 2008 2:07
> > To: General Red Hat Linux discussion list
> > Subject: Re: SSH Consent Banner
> >
> > Actually, this worked for me. I created a separate script
> > that is called
> > within /etc/bashrc. This is what happens. It is probably
> > considered crude,
> > but it works for me. Please let me know if there is a flaw in
> > this approach.
> >
> > Thanks.
> >
> > Paul
> >
> > HOSTNAME=`hostname`
> > GREET=`cat /etc/issue`
> > echo $GREET
> > echo "Do you agree to this consent? [Y/N]"
> > read answer
> >
> > case $answer in
> >
> > Y|y)
> > echo "Welcome to $HOSTNAME."
> > ;;
> >
> > N|n)
> > echo "Goodbye."
> > sleep 2
> > PID=`ps -ef | grep ssh_test_1 | awk ' {print $3} '`
> > kill -9 $PID
> > ;;
> >
> > *)
> > echo "Goodbye. Try SSH again"
> > echo "You Must enter a Y or a N "
> > sleep 2
> > PID=`ps -ef | grep ssh_test_1 | awk ' {print $3} '`
> > kill -9 $PID
> > ;;
> >
> > esac
> >
> >
> >
> > On 2/1/08 7:21 PM, "Nikolas Lam"
> > <nlam87346@(protected):
> >
> > >
> > >
> > > On Fri, 2008-02-01 at 11:08 -0500, Paul Whitney wrote:
> > >> Can someone tell me how to configure SSHD to present a
> > yes/no prompt? My
> > >> system currently is configured to present a consent
> > banner, but it does not
> > >> require users to agree to the consent. Any help is appreciated.
> > >>
> > >> Paul W.
> > >>
> > >>
> > >
> > > Not sure how to do exactly that, but you could just present
> > something
> > > using
> > >
> > > Banner /etc/ssh_issue
> > >
> > > in /etc/ssh/sshd_config. This will print the contents of
> > /etc/ssh_issue
> > > just before putting in their passwords. In it you could
> > say, entering
> > > your password is agreeing to your terms and conditions.
> > >
> > > Once they log in, they'll also by default get the system's /etc/motd
> > >
> > >
> > > N.
> > >
> > >
> >
> >
> > --
> > redhat-list mailing list
> > unsubscribe mailto:redhat-list-request@(protected)
> > https://www.redhat.com/mailman/listinfo/redhat-list
> >
>
>
>
>------------------------------
>
>Message: 6
>Date: Mon, 11 Feb 2008 11:27:30 +0100
>From: "Mertens, Bram" <mertensb@(protected)>
>Subject: Keyboard layout problem in XEN virtual machine
>To: "General Red Hat Linux discussion list" <redhat-list@(protected)>
>Message-ID:
> <E4763D73EF6E4848853562C30CA5A9AF012791D0@(protected)>
>Content-Type: text/plain; charset="us-ascii"
>
>Hi
>
>My office uses a number of Windows-only tools which is forcing me to
>reboot into Windows several times a say. To avoid this I'd like to set
>up a virtual machine (using XEN) so I can run those tools in it.
>
>After strugling to get Windows XP to install (halfway during the
>installation it forces a restart and after this it wouldn't find the CD)
>I discovered that even though all the keyboard and language settings are
>in XP the keyboard layout is still wrong. We use azerty keyboards and I
>have configured the virtual machine as such but *after the installation*
>the keyboard is interpreted as querty. I stress *after the
>installation* because somewhere during the installation you can change
>the keyboard layout - which I did - and after that the keyboard layout
>was interpreted correctly by the installation program.
>
>How can I configure the virtual machine to recognize my keyboard as
>azerty (be-latin1)?
>
>Regards
>
>Bram
>
>
>
>Mazda Motor Logistics Europe NV, Blaasveldstraat 162, B-2830 Willebroek
>VAT BE 406.024.281, RPR Mechelen, ING 310-0092504-52, IBAN : BE64 3100
>0925 0452, SWIFT : BBRUBEBB
>
>
>
>
>------------------------------
>
>Message: 7
>Date: Mon, 11 Feb 2008 09:27:01 -0500
>From: Margaret Doll <Margaret_Doll@(protected)>
>Subject: "smbclient -L servername -N" not working
>To: samba <samba@(protected)
> list <redhat-list@(protected)>
>Message-ID: <BE07593D-7D9C-4244-A96C-869ACC752E20@(protected)>
>Content-Type: text/plain; charset=US-ASCII; format=flowed; delsp=yes
>
>I would appreciate any ideas on how to correct the problem that we are
>having that is outlined below. Thanks for your help.
>
>I have been running samba for a long time. Currently we are having
>problems with it filling up /var/log/messages with
>
>Feb 7 10:45:02 servername smbd[2157]: Can't become connected user!
>Feb 7 10:45:02 servername smbd[2158]: [2008/02/07 10:45:02, 0] smbd/
>service.c:make_connec
>tion_snum(928)
>
>In doing the list of checks on samba and nmbd, I find that only
>
>smbclient -L servername -N
>Anonymous login successful
>Domain=[DEPT] OS=[Unix] Server=[Samba 3.0.25b-1.el4_6.4]
>tree connect failed: NT_STATUS_LOGON_FAILURE
>
>doesn't work.
>
>smbclient -L servername -U username
>
>works fine.
>
>
>rpm -aq | grep samba
>samba-common-3.0.25b-1.el4_6.4
>samba-client-3.0.25b-1.el4_6.4
>system-config-samba-1.2.21-1.el4.1
>samba-3.0.25b-1.el4_6.4
>samba-swat-3.0.25b-1.el4_6.4
>
>uname -r
>2.6.9-67.0.1.ELsmp
>
>Our guest account, chemug in samba, cannot log into the system.
>Regular accounts on samba are having no
>problems connecting to and printing through our server.
>
>
>more smb.conf
># Global parameters
>
>[global]
> workgroup = DEPT
>
> netbios name = servername
> server string = servername - DEPT Samba Server
> interfaces = 128.148.nn.nn/24 127.0.0.1
>
> security = user
> smb passwd file = /etc/samba/smbpasswd
>
> log file = /var/log/samba/log.%m
> max log size = 50
> socket options = TCP_NODELAY SO_RCVBUF=8192 SO_SNDBUF=8192
> dns proxy = yes
> os level = 255
> preferred master = yes
>
> domain master = yes
># Added 1/7/06
> local master = yes
> wins proxy = no
> wins support = yes
>
># Added 9/06
> password server = yes
>#
># Added to reduce network traffic
> name resolve order = host wins bcast
>
> remote announce = 128.148.nn.255/DEPT 128.148.mmm.255/DEPT
>128.148.ooo.255/DEPT 128.148.ppp.255/DEPT 128.148.qqq.255/DEPT
>
> invalid users = bin daemon sys adm tty disk lp mem kmem wheel mail
>news uucp m
>an games gopher dip ftp floppy utmp xfs console pppusers popusers
>slipusers slocate gd
>m filesystem root
> valid users = @deptusers @dept2users @users @stockroom @guest
> username map = /etc/samba/smbusers
> domain logons = yes
> guest ok = yes
>
> guest account = chemug
> hosts allow = 128.148.mmm. 128.148.nn. 128.148.ooo. 128.148.ppp.
>128.148.qqq.
>128.148.rrr.31 128.148.rrr.10 127.
> dos filetimes = Yes
> dos filetime resolution = Yes
>## Changes for cups
> load printers = yes
> printing = cups
> printcap name = /etc/printcap
>
># Helps to eliminate "Access Denied"
># on Windows NT, 2000, and XP
>#
> password server = None
> use client driver = yes
>
># Add 9/06
>
> disable spoolss = yes
>
>[homes]
> comment = Home Directories
> writeable = yes
>[printers]
> comment = All Printers
> path = /var/spool/samba
> guest ok = Yes
> printable = Yes
>
>[1-Mac]
> comment = Distributed Software for MacIntoshes
> path = /chemusers/1-Mac
> volume = Utilities for MacIntoshes
> guest ok = yes
>[1-Win]
> comment = Distributed Software for Windows
> path = /chemusers/1-Win
> volume = Utilities for Window Computers
> guest ok = yes
>
>[Milling]
> comment = Contains the drop boxes for Milling requests
> path = /chemusers/milling
> volume = Milling Drop Box
> writeable = yes
> valid users = @chemusers
> force group = chemusers
>
>[Stockroom]
> comment = Database for the Stockroom Applications
> path = /home/stockroom
> volume = Database for the Stockroom
> valid users = @stockroom
> writeable = yes
> create mask = 660
> directory mask = 0770
>
>netstat -nlp | grep LISTEN| grep -v LISTENING
>
>tcp 0 0 0.0.0.0:905
>0.0.0.0:* LISTEN 4115/rpc.statd
>
>tcp 0 0 0.0.0.0:781
>0.0.0.0:* LISTEN 4418/rpc.mountd
>tcp 0 0 0.0.0.0:111
>0.0.0.0:* LISTEN 4095/portmap
>
>tcp 0 0 0.0.0.0:445
>0.0.0.0:* LISTEN 29710/smbd
>tcp 0 0 0.0.0.0:767
>0.0.0.0:* LISTEN 4403/rpc.rquotad
>
>
>
>------------------------------
>
>Message: 8
>Date: Mon, 11 Feb 2008 11:53:52 -0500
>From: Kirk Wight <kirk@(protected)>
>Subject: RE: Disk partitions and LVM limits
>To: "redhat-list@(protected)>
>Message-ID: <C3D5E7D0.10168%kirk@(protected)>
>Content-Type: text/plain; charset="ISO-8859-1"
>
>Hi Peter,
>I'm also running a Dell MD1000 in RAID5 on a CentOS system (4.6), with LVM
>on ext3.
>I never came across a 2TB limit or your particular errors... I had one 1.4TB
>LVM volume which I extended into the 3.6TB of the MD1000, for one large 5TB
>LVM volume (mounted on root). The only problem I had was getting the driver
>loaded at boot time (solved with a new initrc). I hope this helps...
>Kirk
>--
>
>Kirk Wight
>Administrateur de systèmes / Systems Administrator
>kirk@(protected)
>
>
>
>
>
>------------------------------
>
>__
>redhat-list mailing list
>Unsubscribe mailto:redhat-list-request@(protected)
>https://www.redhat.com/mailman/listinfo/redhat-list
>
>End of redhat-list Digest, Vol 48, Issue 9
>******************************************
>
>
>
>
>--
>No virus found in this incoming message.
>Checked by AVG Free Edition.
>Version: 7.5.516 / Virus Database: 269.20.2/1271 - Release Date: 2/11/2008
>8:16 AM
--
No virus found in this outgoing message.
Checked by AVG Free Edition.
Version: 7.5.516 / Virus Database: 269.20.2/1271 - Release Date: 2/11/2008 8:16 AM
--
redhat-list mailing list
unsubscribe mailto:redhat-list-request@(protected)
https://www.redhat.com/mailman/listinfo/redhat-list
