  | | | Broadcom 4328 Pre-N Wireless Device | Broadcom 4328 Pre-N Wireless Device 2007-03-09 - By Raab Nelson
Back Hello all,
I am running 2.6.19-2911.6.5 on an x86_64 laptop. I've gotten all the devices installed except for the Pre-N Wifi card that came with this guy. I'm running the fc6 distro, do you all know of any buildable/pre-build drivers for this device existing?
Here's some lspci output: 01:00.0 Network controller: Broadcom Corporation Unknown device 4328 (rev 03) Subsystem: Hewlett-Packard Company Unknown device 1366 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 11 Region 0: Memory at b3000000 (64-bit, non-prefetchable) [size=16K] Region 2: Memory at d0000000 (64-bit, prefetchable) [size=1M] Capabilities: [40] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=2 PME- Capabilities: [58] Vendor Specific Information Capabilities: [e8] Message Signalled Interrupts: 64bit+ Queue=0/0 Enable- Address: 0000000000000000 Data: 0000 Capabilities: [d0] Express Endpoint IRQ 0 Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag+ Device: Latency L0s <4us, L1 unlimited Device: AtnBtn- AtnInd- PwrInd- Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported- Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- Device: MaxPayload 128 bytes, MaxReadReq 128 bytes Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s, Port 0 Link: Latency L0s <4us, L1 <64us Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch- Link: Speed 2.5Gb/s, Width x1 Capabilities: [100] Advanced Error Reporting Capabilities: [13c] Virtual Channel Capabilities: [160] Device Serial Number 1a-00-06-ff-ff-73-5a-7a Capabilities: [16c] Power Budgeting
Hello all,<br><br>I am running 2.6.19-2911.6.5 on an x86_64 laptop. I' ;ve gotten all the devices installed except for the Pre-N Wifi card that came with this guy. I'm running the fc6 distro, do you all know of any buildable/pre-build drivers for this device existing? <br><br>Here's some lspci output:<br>01:00.0 Network controller: Broadcom Corporation Unknown device 4328 (rev 03)<br>   ; Subsystem: Hewlett-Packard Company Unknown device 1366<br> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- <br> Status: Cap+ 66MHz- UDF- FastB2B - ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-<br > Latency: 0, Cache Line Size: 64 bytes<br> Interrupt: pin A routed to IRQ 11<br> Region 0: Memory at b3000000 (64-bit, non-prefetchable) [size=16K] <br> Region 2: Memory at d0000000 (64 -bit, prefetchable) [size=1M]<br> Capabilities: [40] Power Management version 2<br> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) <br> Status: D0 PME-Enable- DSel=0 DScale=2 PME-<br> Capabilities: [58] Vendor Specific Information<br > Capabilities: [e8] Message Signalled Interrupts: 64bit+ Queue=0/0 Enable-<br> Address: 0000000000000000 Data: 0000 <br> Capabilities: [d0] Express Endpoint IRQ 0<br> Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag+<br> Device: Latency L0s <4us, L1 unlimited <br> Device: AtnBtn- AtnInd- PwrInd- <br> Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported- <br> Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-<br>  ; Device: MaxPayload 128 bytes, MaxReadReq 128 bytes <br> Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s, Port 0<br> Link: Latency L0s <4us, L1 <64us<br> Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-<br>   ; Link: Speed 2.5Gb/s, Width x1<br> Capabilities: [100] Advanced Error Reporting<br> Capabilities: [13c] Virtual Channel<br> Capabilities: [160] Device Serial Number 1a-00-06-ff-ff-73-5a-7a<br>  ; Capabilities: [16c] Power Budgeting <br><br>
__ ____ ____ ____ ____ ____ ____ ____ ____ ____ Redhat-install-list mailing list Redhat-install-list@(protected) https://www.redhat.com/mailman/listinfo/redhat-install-list To Unsubscribe Go To ABOVE URL or send a message to: redhat-install-list-request@(protected) Subject: unsubscribe
|
|
 |