 | | | Connection reset by peer | Connection reset by peer 2007-05-16 - By Tom H
Back
Furnish, Trever G wrote:
> You didn't note where you did your capture (on the client, the server,
> or some intermediary device). Presuming that you did the capture on the
> client, I'd do a similar capture on the server and verify that it's
> really the server sending the rst. Lots of firewalls send RSTs in both
> directions to break connections.
>
I've managed to replicate this with 2 servers that are in the same vlan,
plugged into the same switch. No firewall or suchlike causing the problem.
It's very weird, I'm starting to suspect the Tigon drivers for the
broadcom BCM5703 card. im going to switch back to the bcm driver and see
if it make any difference.
However, I have 12 blades running exactly the same build of RHEL4
x86_64, and only 4 servers that are having the problem, and they are in
different enclosures.
Cheers,
Tom
> If it really does turn out that the server is sending an RST, then I'd
> start the server with debugging output turned on and look for clues
> there.
>
>
>
>> -- --Original Message-- --
>> From: redhat-list-bounces@(protected)
>> [mailto:redhat-list-bounces@(protected)] On Behalf Of Tom H
>> Sent: Wednesday, May 09, 2007 4:58 PM
>> To: redhat-list@(protected)
>> Subject: ssh: Connection reset by peer
>>
>> Hi,
>>
>> I have a couple of RHEL4 which have started disconnecting me
>> during ssh login after I enter the correct password;
>>
>> "Read from remote host msweb01.test.ms.osti.local: Connection
>> reset by peer Connection to msweb01.test.ms.osti.local closed."
>>
>> I turned on -vvv debugging on the client and the relevant section is;
>>
>> debug3: remaining preferred: ,password
>> debug3: authmethod_is_enabled password
>> debug1: Next authentication method: password
>> txxxxxx@(protected)'s password:
>> debug3: packet_send2: adding 48 (len 61 padlen 19 extra_pad 64)
>> debug2: we sent a password packet, wait for reply
>> debug1: Authentication succeeded (password).
>> debug1: channel 0: new [client-session]
>> debug3: ssh_session2_open: channel_new: 0
>> debug2: channel 0: send open
>> debug1: Entering interactive session.
>> debug1: channel 0: free: client-session, nchannels 1
>> debug3: channel 0: status: The following connections are open:
>> #0 client-session (t3 r-1 i0/0 o0/0 fd 4/5 cfd -1)
>>
>> debug3: channel 0: close_fds r 4 w 5 e 6 c -1 Read from
>> remote host msweb01.test.ms.osti.local: Connection reset by
>> peer Connection to msweb01.test.ms.osti.local closed.
>> debug1: Transferred: stdin 0, stdout 0, stderr 126 bytes in
>> 0.2 seconds
>> debug1: Bytes per second: stdin 0.0, stdout 0.0, stderr 703.9
>> debug1: Exit status -1
>>
>>
>> A tcpdump shows that the server is sending a RST, ACK to
>> close the connection. The server debug logs has the following;
>>
>>
>> Apr 27 04:08:24 msweb01 sshd[13481]: debug2: monitor_read: 46
>> used once,
>> disabling now
>> Apr 27 04:08:24 msweb01 sshd[13481]: debug2: monitor_read: 3
>> used once,
>> disabling now
>> Apr 27 04:08:24 msweb01 sshd[13481]: debug2: monitor_read: 4
>> used once,
>> disabling now
>> Apr 27 04:08:24 msweb01 sshd[13481]: debug2: monitor_read: 9
>> used once,
>> disabling now
>> Apr 27 03:08:24 msweb01 sshd[13482]: debug1: userauth_banner: sent
>> Apr 27 03:08:24 msweb01 sshd[13482]: Failed none for txxxxxx from
>> 10.127.5.104 port 4460 ssh2
>> Apr 27 03:08:27 msweb01 sshd[13482]: debug1: userauth-request
>> for user
>> txxxxxx service ssh-connection method password
>> Apr 27 03:08:27 msweb01 sshd[13482]: debug1: attempt 1 failures 1
>> Apr 27 03:08:27 msweb01 sshd[13482]: debug2:
>> input_userauth_request: try
>> method password
>> Apr 27 04:08:27 msweb01 sshd[13481]: debug1: PAM: password
>> authentication accepted for txxxxxx
>> Apr 27 04:08:27 msweb01 sshd[13481]: Accepted password for
>> txxxxxx from
>> 10.127.5.104 port 4460 ssh2
>> Apr 27 03:08:27 msweb01 sshd[13482]: Accepted password for
>> txxxxxx from
>> 10.127.5.104 port 4460 ssh2
>> Apr 27 04:08:27 msweb01 sshd[13481]: debug1: monitor_child_preauth:
>> txxxxxx has been authenticated by privileged process
>> Apr 27 04:08:27 msweb01 sshd[13481]: debug2: mac_init: found hmac-md5
>> Apr 27 04:08:27 msweb01 sshd[13481]: debug2: mac_init: found hmac-md5
>> Apr 27 04:08:27 msweb01 sshd[13481]: debug2: User child is on
>> pid 13484
>> Apr 27 04:08:27 msweb01 sshd[13481]: debug1: do_cleanup
>> Apr 27 04:08:27 msweb01 sshd[13481]: debug1: PAM: cleanup
>>
>>
>>
>> Any ideas on what might cause that?
>>
>> Thanks,
>>
>> Tom
>>
>>
>>
>>
>> --
>> redhat-list mailing list
>> unsubscribe mailto:redhat-list-request@(protected)?subject=unsubscribe
>> https://www.redhat.com/mailman/listinfo/redhat-list
>>
>>
>
>
--
redhat-list mailing list
unsubscribe mailto:redhat-list-request@(protected)?subject=unsubscribe
https://www.redhat.com/mailman/listinfo/redhat-list
|
|
|