 | | | Supported Network Cards? Please | Supported Network Cards? Please 2003-05-13 - By James Stanhope
Back
Try Donald Becker's page at http://www.scyld.com/netork/updates.html
He wrote a number of the network drivers used by RH 7.x and updating from his
site resolved a problem I had with Sundance based D-Link cards.
You will have to install the kernel source and build the driver yourself, but
the process is quite well explained on the site.
James Stanhope.
14/05/03 4:53:16, "jason lunsford" <jason@(protected)> wrote:
>Hello--
>I am trying to set up a Dell PowerEdge 600SC 1.8 GHz, 512 RAM server to run
>ColdFusion MX. I understand fully that I have to be RH 7.2 and under for
>the Verity searches to work (I've had RH 7.3 and 8.0 running all to no avail
>with ColdFusion/Verity).
>
>HOWEVER, I can't get either of my two network cards to initialize in 7.2.
>
>**The server has a Broadcom NetXtreme Gigabit Copper card in slot 3 that I
>can configure in the GUI install in 7.3 and 8.0, but not in 7.2. I see that
>it uses the tg3 driver in 7.3 and 8.
>
>**The server also has an Intel Pro 1000 MT Gigabit card on the motherboard.
>This card (in my RH 8 installs) likes to use the e1000 driver.
>
>I've tried to use the Network Config GUI tool in 7.2 (after i install, not
>during the install), but all I get is "Network interface failed to
>initialize. Check your settings and try again." I've also tried
>editing/creating the following text files:
>
>**/etc/resolv.conf
>nameserver 64.238.96.12
>nameserver 66.180.96.12
>search localdomain
>
>**/etc/sysconfig/network
>NETWORKING=yes
>HOSTNAME=localhost.localdomain
>GATEWAY=10.0.1.1
>
>**/etc/sysconfig/hwconf (which always detects my network cards, but lists
>the driver as "unknown". i put in the correct driver names [tg3 and e1000]
>and save the file)
>
>**/etc/modules.conf (i add the following lines)
>alias eth0 tg3
>alias eth1 e1000
>
>**and i create /etc/sysconfig/networking/devices/ifcfg-eth0:
>DEVICE=eth0
>BOOTPROTO=static
>BROADCAST=10.0.1.255
>IPADDR=10.0.1.130
>NETMASK=255.255.255.0
>NETWORK=10.0.1.0
>ONBOOT=yes
>USERCTL=no
>PEERDNS=no
>GATEWAY=10.0.1.1
>TYPE=Ethernet
>
>**i also create an ifcfg-eth1 that has a different IPADDR
>
>In my Service Configuration GUI tool, I note that Network is checked;
>however, I don't see even a FAIL message on my boot up text screen where it
>goes through all the services and configurations.
>
>In my .../net/modules directory, i see e1000.o, but no tg3.o (i think). do
>i need to compile those or install those or something?
>
>Any help (recommended books, recommended Network cards i could buy for 7.2
>that you guys are using, web pages etc.) is greatly, greatly appreciated.
>
>I sincerely don't want to have to put Windows on this server, but if i can't
>get this 7.2 on the network, using it as a web server probably won't get me
>very far :-(
>
>Thanks in Advance--
>Jason
>
>
>
>__ ____ ____ ____ ____ ____ ____ ____ ____ ____
>enigma-list mailing list
>enigma-list@(protected)
>https://www.redhat.com/mailman/listinfo/enigma-list
>
>
Earn $52 per hosting referral at Lunarpages.
|
|
|