 | | | SATA problems with HP DL140 G2 server | SATA problems with HP DL140 G2 server 2005-09-12 - By Lars Andersson
Back
I'm having trouble with a HP DL-140 G2 server with SATA disks. In both
RHEL 3 and RHEL 4 the disk is found as /dev/hda and disk I/O
is terrible, around 3MBytes/sec instead of the expected 50MBytes/sec.
The server is certified by Red Hat / HP but neither of theese players
have been able to answer my questions regarding this, Red Hat tells me
to talk to HP and HP says "ask red hat".
Have anyone installed RHEL 3 on an DL140 G2 with SATA disks and gotten it
to work? With Ubuntu I get normal performance from the disks on the same server
so there is no hardware failure. I'm unable to set DMA with hdparm.
Here is some info (dmesg, hdparm, hardware, bios etc). Any help is much
appreciated.
lsmod
=====
Module Size Used by Not tainted
audit 90808 2 (autoclean)
usbserial 23868 0 (autoclean) (unused)
lp 9156 0 (autoclean)
parport 38848 0 (autoclean) [lp]
autofs4 16888 0 (autoclean) (unused)
e100 28360 0 (unused)
mii 4088 0 [e100]
tg3 69768 1
ipt_REJECT 4632 1 (autoclean)
ipt_state 1080 5 (autoclean)
ip_conntrack 29800 1 (autoclean) [ipt_state]
iptable_filter 2412 1 (autoclean)
ip_tables 16544 3 [ipt_REJECT ipt_state iptable_filter]
microcode 6912 0 (autoclean)
sg 37388 0 (autoclean)
sr_mod 17880 0 (autoclean)
cdrom 32896 0 (autoclean) [sr_mod]
usb-storage 74912 0
keybdev 2976 0 (unused)
mousedev 5688 0 (unused)
hid 22532 0 (unused)
input 6176 0 [keybdev mousedev hid]
ehci-hcd 20776 0 (unused)
usb-uhci 26860 0 (unused)
usbcore 81152 1 [usbserial usb-storage hid ehci-hcd
usb-uhci]
ext3 89960 2
jbd 55156 2 [ext3]
ata_piix 5320 0 (unused)
scsi_dump_register 2368 0 [ata_piix]
libata 46652 0 [ata_piix]
sd_mod 14128 0 (unused)
scsi_mod 115496 5 [sg sr_mod usb-storage ata_piix libata
sd_mod]
debus=100
==========
I've tried to add a idebus=100 or 133 to the kernel as an boot
argument, it did
not alter the disc I/O.
hdparm -tT /dev/hda
===================
/dev/hda:
Timing buffer-cache reads: 3384 MB in 2.00 seconds = 1692.00 MB/sec
Timing buffered disk reads: 10 MB in 3.16 seconds = 3.16 MB/sec
hdparm /dev/hda
===============
/dev/hda:
multcount = 16 (on)
IO_support = 0 (default 16-bit)
unmaskirq = 0 (off)
using_dma = 0 (off)
keepsettings = 0 (off)
readonly = 0 (off)
readahead = 8 (on)
geometry = 9729/255/63, sectors = 156301488, start = 0
mount
=====
/dev/hda2 on / type ext3 (rw)
none on /proc type proc (rw)
none on /dev/pts type devpts (rw,gid=5,mode=620)
usbdevfs on /proc/bus/usb type usbdevfs (rw)
/dev/hda1 on /boot type ext3 (rw)
none on /dev/shm type tmpfs (rw)
dmesg
=====
Linux version 2.4.21-32.0.1.ELsmp (bhcompile@(protected)) (gcc
version 3.2.3 20030502 (Red Hat Linux 3.2.3-52)) #1 SMP Tue May 17 17:52:23 EDT
2005
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009b800 (usable)
BIOS-e820: 000000000009b800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000ca000 - 00000000000cc000 (reserved)
BIOS-e820: 00000000000dc000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000003ff70000 (usable)
BIOS-e820: 000000003ff70000 - 000000003ff7a000 (ACPI data)
BIOS-e820: 000000003ff7a000 - 000000003ff80000 (ACPI NVS)
BIOS-e820: 000000003ff80000 - 0000000040000000 (reserved)
BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ff800000 - 00000000ffc00000 (reserved)
BIOS-e820: 00000000fffffc00 - 0000000100000000 (reserved)
127MB HIGHMEM available.
896MB LOWMEM available.
found SMP MP-table at 000f6790
hm, page 000f6000 reserved twice.
hm, page 000f7000 reserved twice.
hm, page 0009b000 reserved twice.
hm, page 0009c000 reserved twice.
NX (Execute Disable) protection: active
On node 0 totalpages: 262000
zone(0): 4096 pages.
zone(1): 225280 pages.
zone(2): 32624 pages.
ACPI: Searched entire block, no RSDP was found.
ACPI: RSDP located at physical address c00f67d0
RSD PTR v0 [PTLTD ]
__va_range(0x3ff755b5, 0x28): idx=33 mapped at fffdd000
ACPI table found: RSDT v1 [PTLTD RSDT 1540.0]
__va_range(0x3ff79e54, 0x24): idx=33 mapped at fffdd000
__va_range(0x3ff79e54, 0x74): idx=33 mapped at fffdd000
ACPI table found: FACP v1 [INTEL LINDHRST 1540.0]
__va_range(0x3ff79ec8, 0x24): idx=33 mapped at fffdd000
__va_range(0x3ff79ec8, 0x40): idx=33 mapped at fffdd000
ACPI table found: MCFG v1 [PTLTD MCFG 1540.0]
ACPI: Unsupported table MCFG
__va_range(0x3ff79f08, 0x24): idx=33 mapped at fffdd000
__va_range(0x3ff79f08, 0x50): idx=33 mapped at fffdd000
ACPI table found: SPCR v1 [PTLTD $UCRTBL$ 1540.0]
__va_range(0x3ff79f58, 0x24): idx=33 mapped at fffdd000
__va_range(0x3ff79f58, 0x80): idx=33 mapped at fffdd000
ACPI table found: APIC v1 [PTLTD APIC 1540.0]
__va_range(0x3ff79f58, 0x80): idx=33 mapped at fffdd000
LAPIC (acpi_id[0x0000] id[0x0] enabled[1])
CPU 0 (0x0000) enabledProcessor #0 Unknown CPU [15:4] APIC version 20
LAPIC (acpi_id[0x0001] id[0x1] enabled[1])
CPU 1 (0x0100) enabledProcessor #1 Unknown CPU [15:4] APIC version 20
IOAPIC (id[0x2] address[0xfec00000] global_irq_base[0x0])
IOAPIC (id[0x3] address[0xfec84000] global_irq_base[0x18])
IOAPIC (id[0x4] address[0xfec84400] global_irq_base[0x30])
INT_SRC_OVR (bus[0] irq[0x0] global_irq[0x2] polarity[0x1] trigger[0x1])
INT_SRC_OVR (bus[0] irq[0x9] global_irq[0x9] polarity[0x1] trigger[0x3])
LAPIC_NMI (acpi_id[0x0000] polarity[0x1] trigger[0x1] lint[0x1])
LAPIC_NMI (acpi_id[0x0001] polarity[0x1] trigger[0x1] lint[0x1])
2 CPUs total
Local APIC address fee00000
__va_range(0x3ff79fd8, 0x24): idx=33 mapped at fffdd000
__va_range(0x3ff79fd8, 0x28): idx=33 mapped at fffdd000
ACPI table found: BOOT v1 [PTLTD $SBFTBL$ 1540.0]
Enabling the CPU's according to the ACPI table
Intel MultiProcessor Specification v1.4
Virtual Wire compatibility mode.
OEM ID: HP Product ID: ACE APIC at: 0xFEE00000
I/O APIC #2 Version 32 at 0xFEC00000.
I/O APIC #3 Version 32 at 0xFEC84000.
I/O APIC #4 Version 32 at 0xFEC84400.
Processors: 2
xAPIC support is present
Enabling APIC mode: Flat. Using 3 I/O APICs
Kernel command line: ro ide0=autotune ide1=autotune hda=autotune root=LABEL=/
ide_setup: ide0=autotune
ide_setup: ide1=autotune
ide_setup: hda=autotune
Initializing CPU#0
Detected 2800.215 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 5583.66 BogoMIPS
Page-cache hash table entries: 262144 (order: 8, 1024 KB)
Page-pin hash table entries: 65536 (order: 6, 256 KB)
Dentry cache hash table entries: 131072 (order: 8, 1024 KB)
Inode cache hash table entries: 65536 (order: 7, 512 KB)
Buffer cache hash table entries: 65536 (order: 6, 256 KB)
Memory: 1021176k/1048000k available (1716k kernel code, 23228k reserved, 1302k
data, 228k init, 130496k highmem)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: Trace cache: 12K uops<6>CPU: L2 cache: 1024K
CPU: Physical Processor ID: 0
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: After generic, caps: bfebfbff 20100000 00000000 00000000
CPU: Common caps: bfebfbff 20100000 00000000 00000000
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.40 (20010327) Richard Gooch (rgooch@(protected))
mtrr: detected mtrr type: Intel
CPU: Trace cache: 12K uops<6>CPU: L2 cache: 1024K
CPU: Physical Processor ID: 0
Intel machine check reporting enabled on CPU#0.
CPU: After generic, caps: bfebfbff 20100000 00000000 00000000
CPU: Common caps: bfebfbff 20100000 00000000 00000000
CPU0: Intel(R) Xeon(TM) CPU 2.80GHz stepping 01
per-CPU timeslice cutoff: 2925.31 usecs.
task migration cache decay timeout: 10 msecs.
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Booting processor 1/1 eip 2000
Initializing CPU#1
masked ExtINT on CPU#1
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Calibrating delay loop... 5596.77 BogoMIPS
CPU: Trace cache: 12K uops<6>CPU: L2 cache: 1024K
CPU: Physical Processor ID: 0
Intel machine check reporting enabled on CPU#1.
CPU: After generic, caps: bfebfbff 20100000 00000000 00000000
CPU: Common caps: bfebfbff 20100000 00000000 00000000
CPU1: Intel(R) Xeon(TM) CPU 2.80GHz stepping 01
Total of 2 processors activated (11180.44 BogoMIPS).
ENABLING IO-APIC IRQs
Setting 2 in the phys_id_present_map
...changing IO-APIC physical APIC ID to 2 ... ok.
Setting 3 in the phys_id_present_map
...changing IO-APIC physical APIC ID to 3 ... ok.
Setting 4 in the phys_id_present_map
...changing IO-APIC physical APIC ID to 4 ... ok.
init IO_APIC IRQs
IO-APIC (apicid-pin) 2-0, 2-3, 2-5, 2-10, 2-11, 2-20, 2-21, 2-22, 3-1, 3-2, 3
-3, 3-4, 3-5, 3-6, 3-7, 3-8, 3-9, 3-10, 3-11, 3-12, 3-13, 3-14, 3-15, 3-16, 3-17
, 3-18, 3-19, 3-20, 3-21, 3-22, 3-23, 4-0, 4-1, 4-2, 4-3, 4-4, 4-5, 4-6, 4-7, 4
-8, 4-9, 4-10, 4-11, 4-12, 4-13, 4-14, 4-15, 4-16, 4-17, 4-18, 4-19, 4-20, 4-21,
4-22, 4-23 not connected.
..TIMER: vector=0x31 pin1=2 pin2=0
number of MP IRQ sources: 22.
number of IO-APIC #2 registers: 24.
number of IO-APIC #3 registers: 24.
number of IO-APIC #4 registers: 24.
testing the IO APIC.......................
IO APIC #2......
.... register #00: 02000000
....... : physical APIC id: 02
....... : Delivery Type: 0
....... : LTS : 0
.... register #01: 00178020
....... : max redirection entries: 0017
....... : PRQ implemented: 1
....... : IO APIC version: 0020
.... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
00 000 00 1 0 0 0 0 0 0 00
01 003 03 0 0 0 0 0 1 1 39
02 003 03 0 0 0 0 0 1 1 31
03 000 00 1 0 0 0 0 0 0 00
04 003 03 0 0 0 0 0 1 1 41
05 000 00 1 0 0 0 0 0 0 00
06 003 03 0 0 0 0 0 1 1 49
07 003 03 0 0 0 0 0 1 1 51
08 003 03 0 0 0 0 0 1 1 59
09 003 03 0 0 0 0 0 1 1 61
0a 000 00 1 0 0 0 0 0 0 00
0b 000 00 1 0 0 0 0 0 0 00
0c 003 03 0 0 0 0 0 1 1 69
0d 003 03 0 0 0 0 0 1 1 71
0e 003 03 0 0 0 0 0 1 1 79
0f 003 03 0 0 0 0 0 1 1 81
10 003 03 1 1 0 1 0 1 1 89
11 003 03 1 1 0 1 0 1 1 91
12 003 03 1 1 0 1 0 1 1 99
13 003 03 1 1 0 1 0 1 1 A1
14 000 00 1 0 0 0 0 0 0 00
15 000 00 1 0 0 0 0 0 0 00
16 000 00 1 0 0 0 0 0 0 00
17 003 03 1 1 0 1 0 1 1 A9
IO APIC #3......
.... register #00: 03000000
....... : physical APIC id: 03
....... : Delivery Type: 0
....... : LTS : 0
.... register #01: 00178020
....... : max redirection entries: 0017
....... : PRQ implemented: 1
....... : IO APIC version: 0020
.... register #02: 03000000
....... : arbitration: 03
.... register #03: 00000001
....... : Boot DT : 1
.... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
00 003 03 1 1 0 1 0 1 1 B1
01 000 00 1 0 0 0 0 0 0 00
02 000 00 1 0 0 0 0 0 0 00
03 000 00 1 0 0 0 0 0 0 00
04 000 00 1 0 0 0 0 0 0 00
05 000 00 1 0 0 0 0 0 0 00
06 000 00 1 0 0 0 0 0 0 00
07 000 00 1 0 0 0 0 0 0 00
08 000 00 1 0 0 0 0 0 0 00
09 000 00 1 0 0 0 0 0 0 00
0a 000 00 1 0 0 0 0 0 0 00
0b 000 00 1 0 0 0 0 0 0 00
0c 000 00 1 0 0 0 0 0 0 00
0d 000 00 1 0 0 0 0 0 0 00
0e 000 00 1 0 0 0 0 0 0 00
0f 000 00 1 0 0 0 0 0 0 00
10 000 00 1 0 0 0 0 0 0 00
11 000 00 1 0 0 0 0 0 0 00
12 000 00 1 0 0 0 0 0 0 00
13 000 00 1 0 0 0 0 0 0 00
14 000 00 1 0 0 0 0 0 0 00
15 000 00 1 0 0 0 0 0 0 00
16 000 00 1 0 0 0 0 0 0 00
17 000 00 1 0 0 0 0 0 0 00
IO APIC #4......
.... register #00: 04000000
....... : physical APIC id: 04
....... : Delivery Type: 0
....... : LTS : 0
.... register #01: 00178020
....... : max redirection entries: 0017
....... : PRQ implemented: 1
....... : IO APIC version: 0020
.... register #02: 04000000
....... : arbitration: 04
.... register #03: 00000001
....... : Boot DT : 1
.... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
00 000 00 1 0 0 0 0 0 0 00
01 000 00 1 0 0 0 0 0 0 00
02 000 00 1 0 0 0 0 0 0 00
03 000 00 1 0 0 0 0 0 0 00
04 000 00 1 0 0 0 0 0 0 00
05 000 00 1 0 0 0 0 0 0 00
06 000 00 1 0 0 0 0 0 0 00
07 000 00 1 0 0 0 0 0 0 00
08 000 00 1 0 0 0 0 0 0 00
09 000 00 1 0 0 0 0 0 0 00
0a 000 00 1 0 0 0 0 0 0 00
0b 000 00 1 0 0 0 0 0 0 00
0c 000 00 1 0 0 0 0 0 0 00
0d 000 00 1 0 0 0 0 0 0 00
0e 000 00 1 0 0 0 0 0 0 00
0f 000 00 1 0 0 0 0 0 0 00
10 000 00 1 0 0 0 0 0 0 00
11 000 00 1 0 0 0 0 0 0 00
12 000 00 1 0 0 0 0 0 0 00
13 000 00 1 0 0 0 0 0 0 00
14 000 00 1 0 0 0 0 0 0 00
15 000 00 1 0 0 0 0 0 0 00
16 000 00 1 0 0 0 0 0 0 00
17 000 00 1 0 0 0 0 0 0 00
IRQ to pin mappings:
IRQ0 -> 0:2
IRQ1 -> 0:1
IRQ4 -> 0:4
IRQ6 -> 0:6
IRQ7 -> 0:7
IRQ8 -> 0:8
IRQ9 -> 0:9
IRQ12 -> 0:12
IRQ13 -> 0:13
IRQ14 -> 0:14
IRQ15 -> 0:15
IRQ16 -> 0:16
IRQ17 -> 0:17
IRQ18 -> 0:18
IRQ19 -> 0:19
IRQ23 -> 0:23
IRQ24 -> 1:0
.................................... done.
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 2800.2947 MHz.
..... host bus clock speed is 200.0209 MHz.
cpu: 0, clocks: 2000209, slice: 666736
CPU0<T0:2000208,T1:1333472,D:0,S:666736,C:2000209>
cpu: 1, clocks: 2000209, slice: 666736
CPU1<T0:2000208,T1:666736,D:0,S:666736,C:2000209>
cpu_sibling_map[0] = 1
cpu_sibling_map[1] = 0
mapping CPU#0's runqueue to CPU#1's runqueue.
zapping low mappings.
Process timing init...done.
Starting migration thread for cpu 0
Starting migration thread for cpu 1
PCI: PCI BIOS revision 2.10 entry at 0xfd83a, last bus=7
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: Ignoring BAR0-3 of IDE controller 00:1f.2
Transparent bridge - Intel Corp. 82801BA/CA/DB/EB PCI Bridge
PCI: Using IRQ router PIIX [8086/24d0] at 00:1f.0
PCI->APIC IRQ transform: (B0,I2,P0) -> 16
PCI->APIC IRQ transform: (B0,I4,P0) -> 16
PCI->APIC IRQ transform: (B0,I5,P0) -> 16
PCI->APIC IRQ transform: (B0,I29,P0) -> 16
PCI->APIC IRQ transform: (B0,I29,P1) -> 19
PCI->APIC IRQ transform: (B0,I29,P3) -> 23
PCI->APIC IRQ transform: (B0,I31,P0) -> 18
PCI->APIC IRQ transform: (B0,I31,P1) -> 17
PCI: using PPB(B0,I4,P0) to get irq 16
PCI->APIC IRQ transform: (B2,I0,P0) -> 16
PCI: using PPB(B0,I5,P0) to get irq 16
PCI->APIC IRQ transform: (B3,I0,P0) -> 16
PCI->APIC IRQ transform: (B5,I1,P0) -> 24
PCI->APIC IRQ transform: (B7,I1,P0) -> 16
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16)
apm: disabled - APM is not SMP safe.
Total HugeTLB memory allocated, 0
Starting kswapd
allocated 32 pages and 32 bhs reserved for the highmem bounces
VFS: Disk quotas vdquot_6.5.1
aio_setup: num_physpages = 65500
aio_setup: sizeof(struct page) = 60
Hugetlbfs mounted.
pty: 2048 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with MANY_PORTS MULTIPORT SHARE_IRQ
SERIAL_PCI ISAPNP enabled
ttyS0 at 0x03f8 (irq = 4) is a 16550A
Real Time Clock Driver v1.10e
NET4: Frame Diverter 0.46
RAMDISK driver initialized: 256 RAM disks of 8192K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
hda: Maxtor 6Y080M0, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: attached ide-disk driver.
hda: task_no_data_intr: status=0x51 { DriveReady SeekComplete Error }
hda: task_no_data_intr: error=0x04 { DriveStatusError }
hda: task_no_data_intr: status=0x51 { DriveReady SeekComplete Error }
hda: task_no_data_intr: error=0x04 { DriveStatusError }
hda: 156301488 sectors (80026 MB) w/7936KiB Cache, CHS=9729/255/63
ide-floppy driver 0.99.newide
Partition check:
hda: hda1 hda2 hda3
ide-floppy driver 0.99.newide
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
Initializing Cryptographic API
NET4: Linux TCP/IP 1.0 for NET4.0
IP: routing cache hash table of 8192 buckets, 64Kbytes
TCP: Hash tables configured (established 262144 bind 65536)
Linux IP multicast router 0.06 plus PIM-SM
Initializing IPsec netlink socket
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 258k freed
VFS: Mounted root (ext2 filesystem).
SCSI subsystem driver Revision: 1.00
libata version 1.10 loaded.
ata_piix version 1.03
ata: 0x1f0 IDE port busy
PCI: Setting latency timer of device 00:1f.2 to 64
ata1: SATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0x1478 irq 15
ata1: SATA port has no device.
scsi0 : ata_piix
Journalled Block Device driver loaded
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Freeing unused kernel memory: 228k freed
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb-uhci.c: $Revision: 1.275 $ time 17:59:01 May 17 2005
usb-uhci.c: High bandwidth mode enabled
PCI: Setting latency timer of device 00:1d.0 to 64
usb-uhci.c: USB UHCI at I/O 0x1400, IRQ 16
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
PCI: Setting latency timer of device 00:1d.1 to 64
usb-uhci.c: USB UHCI at I/O 0x1420, IRQ 19
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
PCI: Setting latency timer of device 00:1d.7 to 64
ehci-hcd 00:1d.7: Intel Corp. 82801EB USB2
ehci-hcd 00:1d.7: irq 23, pci mem f88a0000
usb.c: new USB bus registered, assigned bus number 3
ehci-hcd 00:1d.7: enabled 64bit PCI DMA
PCI: 00:1d.7 PCI cache line size set incorrectly (0 bytes) by BIOS/FW.
PCI: 00:1d.7 PCI cache line size corrected to 128.
ehci-hcd 00:1d.7: USB 2.0 enabled, EHCI 1.00, driver 2003-Jan-22
hub.c: USB hub found
hub.c: 4 ports detected
usb.c: registered new driver hiddev
usb.c: registered new driver hid
hid-core.c: v1.8.1 Andreas Gal, Vojtech Pavlik <vojtech@(protected)>
hid-core.c: USB HID support drivers
mice: PS/2 mouse device common for all mice
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,2), internal journal
hub.c: connect-debounce failed, port 2 disabled
Adding Swap: 522104k swap-space (priority -1)
hub.c: new USB device 00:1d.7-4, assigned address 2
usb.c: USB device 2 (vend/prod 0x59b/0x15d) is not claimed by any active driver.
Initializing USB Mass Storage driver...
usb.c: registered new driver usb-storage
scsi1 : SCSI emulation for USB Mass Storage devices
Vendor: IOMEGA Model: DVDRW8440E2D-B Rev: UOS1
Type: CD-ROM ANSI SCSI revision: 02
WARNING: USB Mass Storage data integrity not assured
USB Mass Storage device found at 2
USB Mass Storage support registered.
Attached scsi CD-ROM sr0 at scsi1, channel 0, id 0, lun 0
sr0: scsi-1 drive
Uniform CD-ROM driver Revision: 3.12
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,1), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
inserting floppy driver for 2.4.21-32.0.1.ELsmp
Best regards
/Lars
--
Taroon-list mailing list
Taroon-list@(protected)
http://www.redhat.com/mailman/listinfo/taroon-list
Earn $52 per hosting referral at Lunarpages.
|
|
|